Recent Content by Guezen

I've been reading up on intake manifolds and stumbled across the comparison of the CFM+, AFE, and the ATS. From reading this I'm leaning toward getting the CFM+ manifold, but I was wondering if anyone has any input on the BD X-Flow manifold. I've searched, but I can't find any numbers on BD's...

I was slowing down off the express way last week and felt a pretty rough shudder. I took it in to the local shop and had the rear u-joints replaced(again) and the ball joints were also replaced. The mechanic said the front drive shaft had a little play but he didn't replace its' u-joints. Well...

yeah, my foot was definately on the brake. I just wanted to make sure there wasn't a new "safety" feature that would require the transmission to warm up or something to prevent damage.

This just happened on my 2007 5. 9 liter Dodge Quad Cab 4x4. I Started the truck, went to put in gear, stepped on the brake, but shifter would not move. I went in the house came out, and it rolled right into drive. I wondered if there is a sensor for fluid temp on cold days, or fluid movement...

Thanks for the reply's, black is what I was leaning toward I just needed to be reassured. I was a little skeptical because if the box or truck begins to lose it's shine the blacks may be a different shade and not look as good. Also I had a weatherguard on my 98' and I'll definately get...

Hey guys give me your opinion on what will look better a black diamond plate tool box with black bed rails or a regular diamond plate tool box with matching bed rails. My truck is all blacked out right now, except for my 5" stainless tip. I'm having a hard time deciding, any pics of others...

I just got tit back from the dealer, and it's all fixed :D . They did flash the ecm with a few TSB's they are: TSB 18-007-04 - White Smoke, Engine Stumble/Misfire, or Flat Spot in Engine Performance TSB 18-033-04 - Generic Cummins Engine Control Module (ECM) Procedure TSB 18-017-05 -...

It's been off since I first talked to edge. I think I'll go in asking for some TSB updates that some of the guys on here seem to like and tell them it's stalling too, and maybe get it fixed and updated. Thanks for the replys guys.

I went with the actron 9145 code reader, plugged it in and it reads 2 p2509 codes and no p0602, but the odometer says both. I tried to erase them but apparently it will only clear codes after they've been fixied. I also called Edge again and they were no help, they said I might need to get...

It's now been 2 days without the EZ, I still get a little better mpg's and my boost hit 34 psi going uphill (a little high for stock). It's almost like my ecm still thinks the EZ is connected to it. Please guys give me some advice, I'm trying to keep replying to this to keep it on the first...

I just spent the past 2hrs. researching scan tools and I need to decide on 1 of these 4. Actron 9135 or 9145, Equus 3100 or 3110. I know the 9145 and 3110 are better but are they worth the $. I want my baby back strong and healthy like it was before so please help me guys. :{ Which...

This past Saturday I put an Edge EZ on my truck and it ran great, then Sun. about a ¼ mile from my house my truck stalled with the EZ on level 2, but fired right back up and ran fine on 2 the rest of the night, then Mon. it stalled just out of my driveway and again 4 miles away both times I was...

Thanks for the reply Mark, I been out of town so now that I finally have a chance to reply. What is the performance replacement muffler you mentioned, and what does it add to the system? Thanks again

Thanks for the thoughts guys I know the t304 is a better material but is it really needed was more my question. If anyone has the MBRP pipes how do you like them? Thanks again

I've read so many post on exhaust and I'm still unsure with what to get. I'm leaning toward DPPI and their MBRP system for a couple of reasons: 1. I want to keep my spare under the truck (4" pipe) 2. Great experience with DDPI 3. From what I've read they're not too loud but they have a nice...