Search Results for Query: *

I ended up sending my ECM to Auto Computer Specialists to be rebuilt. Cost $250, about 12 days to get it back. It seems to be working okay now.

Joe Mc, thanks. I did look at the Geno's replacement battery cable kit, and it looked like a good way to go, however I decided to make my own. I had the proper cable crimp tool and some cable ends already. While I was at it, I replaced the smaller ground wires too. I used military style battery...

Yesterday I plugged in my scan tool and got a P0122 code (APPS/TPS low voltage). Is that caused by a bad ECM? The WTS light delay problem has returned too. I looks like I will be installing a new ECM.

Thanks to all for your comments and suggestions. I got this truck in 2011 with about 107K miles on it. It now has 218K miles. It has been well cared for and has had a relatively easy life. The motor has always run well and still does run well. This WTS light/fuel pump delay problem started this...

Does anyone know which computer controls the WTS light and fuel pump bump?

For the past couple months the wait to start light is slow to come on for the 1998.5 truck my signature. The lift pump is also slow to cycle on and off at the same time. I wait about 5 to 10 seconds and light comes on and the pump cycles and the motor starts and runs fine. Sometimes the light...

tgrost, I had the same, very annoying, issue with my 98.5. I did all the fixes listed above, cleaned the grounds, added two noise filters, re-routed the ground wire over the alternator, etc. but the unlocking/locking issue always returned after a short while. Then I replaced the alternator...

SDalgleish, Yes,I did. I took these pics before I de-burred the rough edges and painted the bare metal. I didn't want any cut knuckles at some future date. As a side note, it looks like you sure have done a lot to your truck. I'm basically stock...yet. Buzz

I converted my 98.5 Sport in May 2011 using the Headlight Depot lights and the suvlights.com harness. This has been one of the best upgrades I have done to my truck! The lights from Headlight Depot cost less than the harness. Total cost for harness and lights was about $325. The new head lights...

Another problem related to the mid-year engine changes I recently found out was with the factory service manual I ordered for the 1998 trucks. I have a 98. 5 24v. In the diesel fuel system section it says: FUEL DELIVERY SYSTEM—DIESEL POWERED ENGINE Two different fuel systems are used for the...

John, you are absolutely correct. I have done that now. It was a little difficult to get at the steering wheel shaft, but I found a 12" long, 5/16" drill bit that worked and I used the mark made by the set screw on the shaft to locate the correct place to drill. The other set screw fit in the...

Gary, that must have been really scary! Good info and a caution for everyone. I noticed when I installed the new shaft that there was already one hole for a set screw on the steering wheel end of the shaft. I used that hole for one of the set screws, but I did not drill a hole for the second...

I'm glad to be able to share some information. This forum has been very, very helpful to me with various upgrades and repairs for my truck. I may have traded my truck off by now if it wasn't for the information I got from you all on this forum. As it is now, this truck will last me many more...

Ol'TrailDog, So far, what impresses me most about this Borgeson box is that the truck goes where it's pointed. No wandering. There is an over all better feel to the steering, probably due to a combination of the 3. 5 vs 4. 5 turns lock to lock and the variable assist feature. It's not "sports...

The stock steering box on my '98. 5 2wd truck, with about 149K miles on it, had been getting really sloppy over the last couple years. In fact my dear GF refused to drive it when we went on long trips with the truck camper. So a couple weeks ago I crawled under the truck to look at the linkage...

I did that upgrade to my 98. 5 last summer. The instructions above are good. The whole door panel does not need to be removed, but just enough to allow you to get at everything. I think I had to pop about 5 or 6 panel clips, and yes they broke so have some replacement ones available. I think I...

I put the Acu-temp on mine, attached to the line coming out of the trans. Seems very accurate to me. Did some test drives, warmed the trans up, then back in my shop I aimed my infrared temp sensor at the same line and it showed within 4 to 5 degrees of what the gauge was showing.

Looks good Ilian. I did my 98. 5 last year and it was one of the best upgrades on my truck. Had to cut out metal to clear the extra bulb. I bought my headlight assemblies from Headlight depot for $168/pair. I had to drop the bumper a little to get the old out and the new in. The lights are very...

Firefighter, I replaced both upper and lower hinges on my 1998. 5 quad cab about a year ago. Bought the hinges from LMC Truck, http://www.lmctruck.com/icatalog/de/full.aspx?Page=11. Cost about $40 each and seemed to be very good quality. It's not a real easy job replacing the hinges. LMC...

RGiordano, I had exactly the same issue with my 47Re transmission this past summer and FourBarR is correct, there is tons of threads on this forum talking about TC locking and unlocking. This forum is really great! After reading the various fixes talked about I decided to do a test on my...