Search Results for Query: *

here's a new one. What is a CTM? Cycled the plugs on it and everything started working again. Don't know what the CTM does except cause the Cab. to lose power when you unplug it, it sits under the dash just in front of my right knee. I can put my wallet away, what a rekief. Jim G.

odo says no bus, checked all the fuses, all good. I've checked everything I've been able to find from all the other threads, everything seems to check good. I'm thinking this is about to get expensive. Jim G

Had this problem for a little while now I need to get it fixed, emissions test coming due and they will not test with cel on. Started my truck one morning and 30 sec. s later the chime goes off and my gauges all went to 0. 0. I've checked everthing from all the other threads and even put...

I have read every thread on this problem I can find and checked all the suggested fixes and mine still will not go away. Pulled the gauges and reset, ran self test gauges good. checked the connections on the pcm, all three plugs looked good saw no corrosion and repluged several times. checked...

part # 4921511 Good Luck Jim G

When mine went bad the gauge went directly to 80 and stayed there. It's the sender. Get a new one from cummins, much cheaper than Dodge, same part. If you can get the old part. # it will still act as a gauge don't get the newer part # the gauge becomes an idiot light. I'll look for the old...

if you do a search there is a long thread on the aftermarket sec. gen tow mirrirs. in that thread there were several members who where going to rewire heat of power. I believe its a straight power run, but find the thread and check, it even hase a wire diag. somewhere within. GOOD LUCK Jim G

Installed yesterday and what a difference. worth the wait. Rock solid at 65 mph and the convex mirror sure makes it a lot easier to see. no more blind spot. just be careful how the wires run, they are easy to pinch.

Recieved mine yesterday after waiting two weeks. sure enough weather turns cold and snowy, will have to wait till this weekend to install. Sure look nice.

Ordered a set from fenderworld a week ago. They charged my credit card but have not heard a word from them since. You can get one side or the other or as a set as I did and they also have the reinforcement plates, that is if you can get them to ship to you.

yea, when the cel first came on I had a p0237,0216 codes. changed the map right away, and when I bought the new one the dealer said I needed the new harness, which I also installed with the new MAP. After the vp44 and lift pump change the 0216 code dropped but not the 0237. no matter what I...

Thanks John for the troubleshooting help. Well after useing the chart and getting good readings from the MAP, and starting the ECM may have taken a dump, I removed the extra harness that the Dodge dealer sold me with the new MAP and plugged in just the old Harness to the new MAP and GOODBYE...

filally got a chance to check voltage. checked power since that seems to be the code :low voltage line A:. Power was 4. 75 volts, is that to low or is it within range.

well, I had a fuel line going to no. 2 cyl. that I left loose and made a big mess to clean up. the eng. thew the infamous p0216 code at the sametime it threw the 237 so I change the vp44 and lift pump, and those codes dropped right away. It's low on power all the time won't hardly go up a hill...

Ok, removed the cables and clean the ends, cables looked good , reinstalled but still shows the code. Truck has low power and have just replaced the vp44 and lift pump when this whole thing started. only code showing is the p0237, and lift pressure is good.

it would not delete with the obdii reader. haven't driven it for a couple of days , will try to drive it sometime today. what would give it low voltage? and how do you check it?

engine threw a p0237 code so I change the turbo boost sensor (map) sensor. still have the code. Relpaced with sensor I purchased from local dodge dealer with the new harness, so I just payed for the dealers vacation . rechecked all of the connections and they seem fine. 2001 quad cab, auto...

just replaced the vp44, lift pump and turo boost sensor and I still have a p0237 code. rechecked all the connections on the sensor that I got from my local dodge dealer, sensor and new harness. Truck dropped the p0216 code but still have p0237. got any ideas as to where I should go next? 2001...