Search Results for Query: *

PROBLEM: Dodge installed an unshielded wire from the alternator to the negative wire of the passengers battery to the ground wire ofOo. the trans PCM. The solution, shield this top alternator wire and the RF interference issue is solved. I tried all the ground wires, PCM, APPS,connections...

My truck had the same problem, and I ran ground wire from both battery negative sides to the PCM ground, checked and cleaned all grounds, etc and nothing worked. I tried the Goering's box to the PCM ground and the alternator wire and it did not work either. The problem is Dodge installed a...

One of our Cummings' trucks has a 12,000 Mile Marker winch and its solenoid(s) went out. We called Mile Marker and our model solenoid is no longer made and it would cost $250. 00 each to replace if they had it. It has 6 terminals and was hard to locate one. Super winch has a 5 terminal solenoid...

I do believe the problem was the OEM MAP sensor connector was dirty after all, as everything else checked out ok. Cleaned it twice and truck runs great with and without the Quad connected.

I have been out of town for several days. Several days ago I disconnected my quadzilla, which is connected to my MAP senor and have had no P0237 problems for several days so far. I will clean the OEM female connector again and reconnected the quadzilla back up tomorrow, and see what happens...

I am thankful for living in this great country, having great friends, family and god. I also thank those who have served before me, as I have served, and my son is currently in the Army, as a diesel mechanic, protecting our freedom. (He drives a 12v) I really appreciate my wife, who saved my...

Disconnected my quadzilla from the MAP sensor and put the OEM wire connector to the MAP sensor. NOTE: put the OEM MAP connector back on to verify if the quadzilla connection could be causing the P0237, low voltage code. Ran Ohms and volts checks on all MAP wiring and ECM, they all checked out...

Go to Geno's website. I got a cup holder for my son's 98 12v for xmas last year. It attaches to the center console between the seats. His works great, in fact I am getting one for myself. Item Number : CUP-SMOOTHIE-9802 Unit Price: $38. 00

I have 190k on my 1999 truck, same water pump and a/c unit. A/c gets down to 42 degree. . just right for me. Same for our 1998 12v truck with 291,000 miles. As far as prices: example-MAP sensor-Advance Auto $90. 00, NAPA $120. 00, Cummings and Geno's $62. 00. Your best bet is to use Cummings...

I checked the OEM wire MAP connector to the ECU # 8 pin (MAP sensor) and got a resistance reading of . 3 Ohms. . that's good and my voltage was 4. 9... . that's good. Checked the resistance from the MAP sensor "A" to "B" pins and got 585 Ohms each... that's good. In theory the MAP sensor should...

Check out this website for tire diameter vs gear ratio. , This graph shows gear ratios needed for various tire sizes. "4wheelparts.com/aux_incl/gear_ratio.html" Jim Davidson

10/26/2010 11:06 am update Detach the two bolts to the fuel filter and push it aside, this will give you access to the ECM. You need to use a 5/32" ball hex bit to get to the screw that is located in the center of the ECM module, remove this screw and it comes right off. Make sure you...

No, I only replaced the Cumming MAP sensor so far. The break in the MAP sensor "C" wire, grey/red stripe, to the ECM connector is tied into the main right ECM wire harness. My manual shows the MAP sensor prongs as: A wire is orange, B wire is black/light blue, C wire is gray/red stripe wire...

Status update: 10/23/2010 @ 3:23 pm est. The resistance from the MAP wire connector "C" to the disconnected ECM connector pin # 8 is zero..... not good. The resistance from the MAP wire connector "C" to within 8 inches of wiring (from the connector) is ok The resistance from the ECM connector...

10/22/2010 @ 2:18 pm est. Todays test results are as follows for code P0237: The MAP sensor A and B connectors read 4. 96 volts. (BTW, I installed a Cummings MAP sensor several days ago). I put "t-pins" (due to small ECM and MAP connector openings) in both the MAP sensor connector "C" and...

I tried the APPS reset trick and it worked for 10 miles, then the P0237 low voltage code came back and the transmission was slipping again, then the transmission would run ok and slip again. I plan on checking the new Cummings MAP senor in the morning and what ever else I can check to solve this problem...

When driving the truck, the trans slips around 40 to 50 mph. (normal trans lockup at 45 mph). Put new MAP sensor in and it ran great, truck sat for 4 days and when I drove it, the prior problem came back. Any comments? Must be an electrical problem? Now I know why people like the 12v. Items...

I just replaced the damaged coolant sensor electrical cable. This Cummings part number is 3929272, the price for this part is $25. 94, plus ship. The Cummings part number for the coolant temperature sensor is 3920364. The access to these parts is: 1. remove the two fuel filter upper mounting...

The truck is a 98 12v, auto, big tires and lifted. bty (coolant sensor and smoke) Dad.

I have the code P0118, coolant sensor, we broke the coolant sensor connector pulling the head to have it fire ringed and installing cumming marine valve springs. This is my sons truck, He is completing his Army AIT school-diesel mech, and will be home in two weeks on leave before he ships out...