Search Results for Query: *

is there any word on this yet?

My trans finally went. the billet input shaft broke and needs rebuild. So I am thinking on upgrading to a 6 speed auto. I did some searching and it seems like the allison might be the best choice here... I know there alot to do to get this done over rebuilding the 47re. I just dont like...

Here are some vids where my fuel pressure is... . FUEL PRESSURE 4 13 10 pictures by j_k_auto - Photobucket I shimmed the ovf and it is still low. I drove around and it seems to low from what I have read. I am still thinking on getting a adj reg because this ofv just sucks. I tried...

With my mods I have what would you do? I have a option to run a hx40 pro 60/76/18 or the stock turbo. I use this as a dd and run the 1/4 miles through the summer? Looking for the most hp with fuel only..... thanks

How much hp do you get for 1 pound per minute of air flow on a diesel? Some reason we get less on diesels vrs the gassers. Anyone know thanks example: If a turbo flows 69 lbs per minute how much hp with fuel only at the rear wheels? Trying to learn this..... Oo.

I finally got a temp gauge hooked up at the line from filter to injection pump. My pressure is around 10 psi. I pinched the return line and it goes to 60 psi so does that mean my filter is plugged or the ofv is going out? How do you know if the filter is clogged ? thanks

Some testing of my new turbo... Also I am not sure what the whining noise is at 38-40 psi? Anyone know? turbo test video by j_k_auto - Photobucket

I am searching this but it is not coming up. Anyone know this? I am still searching this. Trying to get this done tonight..... Oo. thanks

I would like to upgrade my stock turbo. I am looking for instant spool or quick spool. I am starting to search this. It has been a year since I last searched this. I am also wondering if there is anything new since I last search this. Also I did see they came out with the sequential...

I was wondering if this actually works? I did not get any to try out yet and looking for some feedback..... thanks

I tried a couple of different routes with this. I am wondering about going to the exhaust? I don't want more problems and try to gain less headaches down the road. I am wondering if you run it to the exhaust what are the issues with doing this. I did searching on this all last night and just...

I am trying to test my speed sensor ( the one on the harmonic balancer). I have a green , red , and black wire. I am trying to figure out where these wires go and what they do? Also I am looking for the alt pulley size. Long story but I think I have the wrong pulley on my alt. thanks

I put a 97 6bt in a 95 Chevy that had a 6. 5. I am using the 6. 5 alt I did my conversion a why back and things are going ok with it till today. Anyhow I found out my tach is off. I am not happy about this of course It reads ok near the bottom as it comes up it starts to read off...

I put my springs in a while back. I watched what they will do and such now I am just wondering this. I can rev to 4000 and that is fine. If you are driving it will pull hard to 2500 then it seems like like you over rev it past 2500 and you need to shift. My question is what do I need to...

I worked on my timing for 2 days now. I finally got it figured out how to do this by doing it 20 times... . I over checking everything, Anyhow I got it back together and went to rev it and it slipped timing. I checked everything out again and it seems that the pump gear is not on tight. ...

It was at the spring fling in dillsburg. I am just wondering where this came from? thanks

I searched this and found it very hard to find the spec for the trans torque spec. I am looking for the torque spec for the 1. trans mount to trans. 2. trans mount to cross member. thanks

I need to replace my motor mounts. I am looking for these. Anyone know a good part number for the poly bushing? I have the rubber ones and they did not last so I want to upgrade them to the poly. Hopefully they are stronger. thanks

I was searching and found that the seal can float up the stem. I am wondering if there is a update for this so this does not happen? also I came across this..... I wonder if anyone did this? https://www.turbodieselregister.com/forums/competition-forum/121948-valve-stem-oil-seals.html

Somehow I got this all messed up on my first install. Not sure what is did wrong but I need to know what do I need to keep in the picture. If it is easier I can call someone just pm me. I am just trying to get this done and spend time with mom..... Thanks guys Here is the picture