Search Results for Query: *

I got to redo my battery cable clamps. I have the main positive terminal on the driver side that is rusty and will not tighten any more. Does anyone have any good ideas to redo that without getting to involved in replacing the whole cable or does the cable need to be replaced?

I want to hear if anyone has had any success with Rust Bullett. Thanks

I have a 98 12 valve and I now have a new ford work vehicle and the dodge hasn't got much use as a personal vehicle. I'm kind of between a rock and a hard place as to what to do. The best part is that my grandfather wants to buy the truck for a farm truck, (I guess his duramax doesn't make a...

Heres a product I came across that seems kind of promising to help clean our dirty ac evaporators. You supposely spray it in and it dispenses in a thick foam, and it is suppose to fill up the entire cavity between the evaporator and the fan. As the foam breaks up it is suppose to carry the dirt...

My 98 dodge has started not working as well. Everytime on a hot day when I stop or slow down, the ac compressor will kick off and the ac will not be cold. Does anyone know what can fix this. The compressor was new as of last fall, and I had it vacuumed and recharged. I did change the drier when...

I went out this morning and got in my truck and noticed my dash has cracked right in the middle from front to back. The crack is about 12 inches long. Would this be caused from heat in the sun and does it cause any problems with air flow for my air ducts. Has anyone else had this problem?

My fuel shutoff solenoid is messing up on me. The truck fires up by cranking it over a little longer, or by going under the hood and lifting the plunger all the way up. What is the easiest fix to get it going? Thanks

Here is a interesting device that claims to improve fuel mileage. Anyone familiar with the Hydro 4000 device? Seems like a gimmick but maybe it would work. Any ideas??? Heres there website www.hydro4000.com

does anyone have any tips on replacing a radiator?

Can anyone tell me the cheapest place to find Moog Ball joints. I'm going to put new ones in and was curious if theres a good place to find them cheap.

Does anyone here have good info on how to replace a fan clutch. My fan is on constantly, & we have only had 60-70 degree temps. I believe the clutch is shot. Anyone have any other ideas to the problem. My truck is a 98 12 valve. Thanks

What kind of differences will I notice if I upgrade to a ddp stage 2 injector from my stock injector that have 250,000 miles on them.

I found some cheap set of upper and lower ball joints all selling for 34. 99 by seller "best suspension" Has anyone had any success with these ball joints for a 2wd. They are calling them like OE Brand aftermarket replacements. Is it worth even messing putting these on?

I had a problem this morning with the Manifold Heater. The rubber booties on the studs that bolt up to the manifold heater housing were melting & very hot after I started the truck. Something was shorting out with them causing low voltage in the battery system. My question is, as a quick fix I...

How hard is it to replace the rear axle seal where the driveshaft enters the Dana 80 rearend

Has anybody had any luck with this kit on their manual trucks. It sounds like a good idea for our mechanical 12 valves to have a good high idle setup via the cruise control switch. https://qsol2.cummins.com/info/qsol/products/newparts/clutch_switch_kit.html

I was just curious how hard it would be to convert a 12 valve over to high pressure common rail. Not that I would do it, because the p7100 is so versatile, but can it be done?

I just recently advanced my timing to 15 degrees and adjusted my valves and think I am getting fairly decent mileage with my 12valve. I also pushed my fuel plate half forward for a little extra fuel. This truck now really accelerates harder from 3rd gear on now. I was used to my timing being at...

does anyone know how to remove the front headlight lens cover . someone said you can take them off & scrub them with a majic eraser to remove the yellowing. Any help would be great

all of a sudden to me, it seems a lot of people are having issues with timing/slipped timing. I was curious what is the right torque on that nut. I know the book says 144 ft lbs & some people say that's to low, so what's the correct #?