Search Results for Query: *

I do not get the wait to start on the dash, I do not hear the buss associated with it. Starts and runs fine. I did just remove and replace both batteries, this seemed to occur after that. Any thoughts?

When did the 2ND gen go to the front rotors coming off with just the wheels off and not having to remove the unit bearing, I have a 98. 5 and to remove a rotor is a big job thanks ED

I am now pulling larger 5th wheel with my 98. 5 Dodged diesel I have a DTT trans upgrade but to maintain a cooler trans temp. what is the thought of adding a transmission cooler by either incorporating it into the present system or remove/by pass the existing cooler. Thanks ED

OFF THE TOP OF YOUR HEAD, will I have any fitment problems taking the 99 front and rear diferentials 4:10's and putting them in my 1998. 5. both are 2500 ram 4x4 truck. Bought the 99 with 80,000 miles after it was crashed mostly saved by this humongous aluminum front bumper. Thanks for your input ED

I have a 99 dodge ram 2500 4x4 that I want to tow a 30 foot 5th wheel with. In order to install the Pullrite slider in my shortbed I will need to remove the rear air bags I had installed a while back. How necessary are the air bags with the 5th wheel about 2200 pin weight. over the rear axle...

My boy came over today and for some unknown reason, the ABS light stays on, the Emergency brake light stays on and the speedometer will drop to zero below 20mph. So far all we did is disconnect the battery for about 20 min. and reconnect. We also change the (might be called) the speed sensor in...

I have been excellant about letting the turbo cool to egt of 325* pre turbo before turning motor off. Is this important to do at all times or only after a large hill climb or load or pulling trailer, What is the general consesus on this proceedure ED

Well on my way home I notice 0 oil pressure on the gauge and check gauge light. I have full oil level and I have oil and pressuree going through my Frantz oil filter into the valve cover. any suggestions. thanks ED

My boy dodge 2000 has a leaky fuel filter drain. I leaks at the to plastic hold down nut. What is involved with removing and replacing this part, or any suggestions on how to stop the cap from leaking on the water drain valve. Thanks Ed

What I would like to know is, does the twist control on the dash for temperature cycle off the compressor by turning it up warmer or does it just blend hot air. This is for my 98. 5 dodge diesel. I would like to use it if it will reduce the time the compressor runs, but if not it seems more...

My boy is looking at a 2000 dodge diesel. 4x4 it is far away so he is asking as many questions as possible I told him to stay away from the 53 Block he had the owner crawl under and said he sees a 58. could it be a 58 block or is he miss reading a 53 block. Need to clearify b4 he goes a few...

Has anyone had a problem with clearing codes using ther Scangauge II. I can have a code and it will ask me to clear codes then when I push yes I get a blank screen. Your experience appreciated Ed

Well the title says it all, I wanted your opinion on using some extra ss brake lines I have for the engine oil lines for the frantz filter set up. Will it hold up, works for the harsher brake fluid. ED

what is the trick to get the door to work easily on the center console when you install the Geno's cup smoothy holder???????????????? I did a search and did not come up with anything, but do remember reading about it a long time ago.

I put the hummer h2 wheels on my Dodge 98. 5 4x4 that is ok but when I read about the caps I keep seeing one with the 8 tabs that grab the lug nuts. My caps have a solid ring in the back that I slitted and had to spread out to grab the groove in the center of the hummer rim. they would not in...

can anyone tell me the wheel dimension on the 1998. 5 24v Dodge. 8lug, lug to lug center spacing, back spacing, and wheel width, and center hub diameter. A fellow has some chevy wheels 8 lug 6. 5 center to center lug spacing, 8" rims, and 5" center for hubs. not sure on back spacing. I...

I freed up the frozen blade on the packbrake and then cleaned and got the vacuum solenoid working now I really can't tell it is working. I can see the arm on the vacuum cylinder extending, I can see the arm in the turbo turning I can hear a flutter and fill a restriction of gas at the tail pipe<...