Search Results for Query: *

Hey guys. I’m replacing all my sensors for preventative maintenance since I still have the originals installed. I already did the camshaft sensor. Genos garage lists the 2001 as having a crankshaft position sensor as well. I didn’t think my 2001 had one? Does anyone know for sure if I have one...

Hi. So I think I screwed up by trusting my fuel guage and letting my tank go to 1/8 full. I parked it on a slope and when I returned it started and then quickly died. I tried bleeding it after pushing the truck to a level spot. While cranking a bit more I got the check engine light and the...

Hey guys and gals. What is the best turbo heat wrap out there? I’m trying to limit the amount of heat coming off my turbo since it’s damaging some lines I installed on that side of the engine bay. I’m assuming most heat comes off the turbo and not the exhaust pipe. Or should I wrap that also...

I have a fuel tank question for you all.. I know there’s a roll over safety valve on top of the fuel canister.. Is there some type of valve on the fill line? I’ve heard there might be an anti siphon screen of some sort. Any way to break through that screen? I’m trying to plumb in a fuel...

Anyone know what this connector goes to? I found the wires cut and was wondering where they should go. Thanks.

My alternator is intermittently going into overvoltage mode. I recently had it rebuilt and it worked fine for a few weeks. When it returns to normal it still reads a bit high at around 15 volts. It’s not getting warm or giving any other symptoms. Battery cables and connections are clean and...

I’m replacing my A/C compressor and filter/drier. I’m also replacing my fixed orifice with a replaceable inline orifice tube. I am unable to replace the whole line at this time. The A/C parts guy sold me an orifice for a Ford(the one on the left) he had an orifice for a Dodge but it didn’t fit...

Hey guys. I’ve contacted a few places that reproduce door jamb VIN labels but they all say they need a picture of my old label to reproduce it. Unfortunately I don’t have a picture. I went to the local DMV with proof of my repair and they stuck a ****ty little label on my door. I would really...

Hey guys. I’m heading for some very high altitude camping soon and expect some below freezing temps at night. Also expecting to get some really low quality diesel fill ups. My question to you all is if you think maybe I might need some fuel heaters for my FASS system. I see from their website...

Getting ready to replace my oil cooler/hoses/thermostat/coolant. Just wondering if any one had any tips/suggestions like how much coolant to buy, etc. Thanks.

Traveling cross country I thought it would be time to replace my stock clutch that had 160K miles. Since I was going through central Texas I thought I’d take my truck to the experts at Standard Gear and Transmission in Fort Worth. I’m sure glad I did. While they had my clutch out they found my...

Hello. I’m looking at swapping all my rear axle bearings and seals. I was wondering if anyone had all the part #’s for Timken bearings. I have the Dana 80 with rear disks if that makes any difference. Thanks.

Hi guys. I’m posting this for a guy stuck in Ely, Nevada. He put DEF fluid in his diesel tank and drove it until it died. He changed filters but it won’t start. He’s sitting in front of the Love’s truck stop and the local mechanic quoted him $12,000 for a complete swap of EVERYTHING in his fuel...

Hello. I’m looking for a good Dodge diesel mechanic in the Los Angeles area. I need to change out the clutch on my NV5600 and I don’t want to entrust it to just any mechanic. Thank you.

Hello. I’m looking at doing a complete overhaul of my brakes(new rotors, calipers, and pads). I was just wondering if there’s any difference between the cheap rebuilt calipers and rotors and the expensive ones. I was thinking about going with the pads from Genos garage. Any input would be...

Hello everyone. I have lost all of my plastic fasteners for my windshield cowl(part #14 from the attached chart). Has anybody figured out a replacement for these yet? The dealer says he can’t get them anymore. Thanks in advance for the replies.

Well I called South Bend Clutch today and they recommended one of these units for my truck. I was wondering if anybody else is running this clutch and how they like it? I’m worried about added pedal pressure/smooth engagement. I’ve already installed their clutch master/slave unit. Also, if...

I think it may be time for a new vacuum pump/power steering combo. I’ve noticed in the morning my power steering is stiff for a while and it takes like 30 min. driving before my exhaust brake works. Also when I go down a long grade I intermittently lose my exhaust brake. I did the Gould seal...

My passenger side mirror gave up the other day on a long washboard dirt road. It won’t stay in adjustment and is all loose. Has anybody come up with a cheap fix for this? I have the manual towing mirrors and I’m thinking to upgrade to the powered mirrors. I’m not sure if my base model ST work...

I’m on my third mechanical fuel pressure gauge isolator from Vulcan enterprises. The seal keeps blowing out and putting diesel fuel in my guage. Does anyone know of a better mouse trap? 126163EA-686B-4AA6-9E93-EC0840019DE8 by dblake posted Jul 8, 2018 at 10:18 PM