Search Results for Query: *

I've been getting the P2121 code for awhile now, did the obvious and replaced the pedal but it came back. Today I decided to dig into it with an article I found to check the voltage. With my scan tool the voltage is within spec at all tests however when I go under the hood and wiggle the big...

Hey All I put the MaxTrac 6" lift kit on my 06 Ram 2500 2WD but now the upper control arms are bottoming out on the strut mount. Does anyone have any recommendations for replacements?

Went out today to start the truck that's been sitting for a month or so. Haven't driven it much because of the insane diesel prices in this country. I had battery tenders on both batteries. Put the key in the ignition and I noticed that the P N R D 1 2 display was not coming up, Just showed the...

I've been getting a couple codes lately that come and go. I've noticed the trans hunting for 2nd and 3rd and sometimes you can hear it really clunk into gear. I've already replaced the transducer and ats pressure solenoid. Should I replace the entire valve body or bite the bullet and drop the...

I was out setting valve lash this afternoon and noticed that the #2 intake rocker arm was always able to wiggle back and forth. I went through the rotations of TDC and then BDC just to see if the arm work tighten up like it should. Anyone know what could be causing this? New engine with only...

2006 Ram 2500 5.9 cummins AT is throwing some codes. I just dropped a new motor in it, truck has been sitting since about 2015 at my father in-laws. Right now it's throwing codes- P0868-Transmission fluid Pressure sensor - low P0713-Transmission fluid pressure sensor- high input P1750-solenoid...

Got my new engine fired up today but I noticed the supply line quick connect is leaking. You can see it in the picture leaking by the blue clips. Is there an o ring on the inside of that or should I just buy a new one? That's a 3/8 quick connect right ?

I installed the duel fuel filter system from throttle up industries and one of the compression sleeves has cracks on the edges and build up inside. Anyone know where I can get one of these exact sleeves? I tried a brass sleeve but it didn't work, I brought the fittings together but the fuel line...

I bought this fuel filter adapter to replace the stock fuel filter/water separator system. Do I need to buy another water separator now that I've removed the factory system? https://www.xtremediesel.com/xdp-cummins-cat-filter-adapter-xd232 *** I decided to go with another dual filter (water...

I can't decide which way to go on my injectors. Do I fork over the insane amount of money for 6 new injectors or do I find a reputable shop to rebuild my current injectors? The price of new injectors are silly high to me. Or I could spend $35 each to test out my current injectors. I'd prefer to...

Spent the last 5 hours trying to drop a new 5.9 cummins engine in. This damn thing will not go in. 1st I tried with the oil pan on and that was a epic fail. Dropped oil pan and goes in a little further but I can't get the motor mounts to line up. Tried dropping it in at an angle, nope. Got...

I bought the Fleece performance coolant bypass kit for my 06 Dodge 2500 5.9 block. The bolts that came with the kit do not thread in. Anyone know what size these threads are circled in the picture. The bolts that came with the kit are too big. The bolts for the rear main seal housing are too big.

Is there a way to roll the rear drivers window down without power? Engine is currently out of the truck and I had to replace that window. I only need to roll it down about 3-5 inches to seat the weather stripping around it. *Edit* I got the window down by taking out the 4 motor bolts and was...

Hey All, New to the forum. Working on a 2006 Ram 2500 5.9 cummins that has a loud knock at idle and rev. I pull the valve cover thinking it was one of the injectors and found the #2 cylinder lifter rod off the rocker arm. The lifter rod is not bent. Any idea what would cause thing? I'm guessing...