Search Results for Query: *

I just get the Wheel Stud Recall for my 2012 3500 - I thought the recall was for newer models?

How do I find out if my 2012 Ram 3500 ST clock spring is a 28 terminal - or - a 24 terminal so I know what to order before I remove the airbag and etc?

I have a 2012 Ram 3500 ST. Clock went blank while driving (but radio worked fine...) - tried to set time - screen said = "Clock Unavailable" Got home shut truck off. Next morning Radio and clock not working. Un-hooked batteries for an hour - re-hooked - still no radio or clock. I'll check...

What is the average or common mileage for these to begin to fail?? - Especially if filters have been changed like clockwork regularly.

I have bought 6 from Genos - but now I have 6 extra of the Mopar frame mounted fuel assembly's. It's only $39.00 but I really don't need more assembly's. Plus the motor located nano fuel filter is $77.00 without the canister - filter only... Ha, Ha, Ha... This is ignorant...

I have a 2012 Ram 3500 4WD Crew Cab ST DUALLY (DRW). I bought it used with 140,000 miles. However, after spending almost 3 days trying to match up the 3 REAR MAIN driveshaft U-Joints for a DUALLY (DRW)- Come to find out my driveshaft calls for SINGLE Rear Wheel U-Joints (SRW) Is this normal or...

If you don't have a cutting torch or large torch and the small hand held propane torches won't work - you can use a salamander / torpedo heater to get the job done.

Is it possible to run my 2012 3500 4WD without the front drive shaft in - until my U-Joints come in? I need to make a couple deliveries (200 mile round trip per delivery) before I can get the front U-joints changed. One of them is squeaking on occasion. Or will it throw the trans into limp...

The "lights" on the buttons on both the Cruise pad on the right and the dash Control pad on the left - go "OFF" when I turn the wheel to 2 O'clock. Then back on at 3 O'clock as the wheel continues around. This does the same in the reverse direction. (The lights basically "flash" off at 2...

2012 RAM 6.7 (Missing some parts...) (No Codes) Single Tick noise since I bought it with 140,000 miles. Recently the ticking has become a double tick on and off... Could it be the CP3 gear? Or possibly the valves need adjusted? Here's a quick video -

My front axle diff is weeping out the pinion / u-joint seal- Is this seal the same to replace as the rear end differential that the axles must come out and the pinion removed and replaced?

If you are in a pinch situation and need to waterproof an automotive (or just low DC voltage) electrical connection - here is a hack when you have no shrink wrap tube available.

I have an Autel / Maxiscan and it works - but when getting the codes from the truck itself - it shows a P0606 (ECM) / P0685 / P0689 > theses two are related to my Cruise Control not working. The Maxiscan does not show these. I also have a Panlong for android - but I haven't downloaded the...

When I bought my used 2012 Ram 3500 used - as is - the lot had no idea of what this tune (or whatever this is) for the delete was. Does anyone here know what I have in the pic?

I accidentally bought a tube of "Boat Trailer Wheel Bearing Grease" which is made for high salt (ocean water) for backing the trailer in to launch a boat. \ Would this stuff be OK to use on the Cardin joint? (I didn't have my glasses on when purchasing and could only read the "Wheel Bearing"...

Check out my video of how I resolved my issues with greasing the Cardan Joint.

My Experiences Greasing the Double Cardan Joint

Just wondering if anyone else has encountered this... My wiper washer light came on and I filled the reservoir with fluid. (it was a regular brand - nothing special) However, now every time I cold start the truck - the light comes on until I warm start it 2 or 3 times - then the light stays...

On my Cummins 6.7 I change my oil every 12,000 miles. I pull a 28 foot gooseneck trailer and get 10 Miles Per Gallon. With 12,000 miles @ 10 MPG that is 1200 GALLONS. I cut my frame mounted spin on filter open to see how dirty it (and the front / motor - filter) were after 1200 Gallons. Here...

I managed to separate the two halves of the filter housing and remove the inner filter component fiber - then reassemble the two halves - and reinstall under the valve cover. Just my preference to merely destroying the filter housing or running without any housing at all under the valve cover...