Search Results for Query: *

On a 2005 ram3500, can the turbo be removed without removing the exhaust manifold? I have the turbo/exhaust manifold nuts removed (:)). I still need about 2 more inches of drop. Drain pipe is out of the way. Do I have to remove the exhaust pipe from the support bracket and move it out of the way?

My water pump started leaking after 4 years (gates brand Im pretty sure). I now have a dayco, they recommend a flush before install. Is Prestone Flush Solution acceptable for the 5.9L?

constructed my own manometer based off of this thread from the cummins forum : Here Here are some pics of the setup Parts List sourced from Lowes: the 5/8" x 3/4" MHT brass adapter fits easily in the breather vent tube at the bottom of the engine, i secured with a zip tie and made sure it...

Does anyone have any idea what the bolt spec is? Mopar is anywhere from $7 to $10 a bolt.

After my new transmission was installed the gear indicator for D, 2, 1 in conjunction with the gear shift lever wasn't always lighting up even though it was in gear. For D the gear shift lever has a bit of play in it. You can wiggle it ever so slightly to get the indicator to light up. The...

When I had my Randys transmission installed the installer noted that there was oil leaking from the turbo. I had experienced this before when the drain tube didn't have the correct angles to it. I cleaned it up and proceeded to break in my transmission, every so often checking to see if the...

So my 48RE slipped a bit going up a hill in 2nd gear. Was behind a cyclist so traveling around 10 mph. I noticed the transmission slipped once as i was trying to maintain speed. So I adjusted the bands and tested again on the same hill. same result. Full disclosure the 1st time I adjusted the bands on...

Either this has been going on all along or I just noticed it.

After evacuating an AC system, should i open the high side port on the shrader valve (closing the high side port) when charging? The reason I ask is if I'm weighing the R134a going into the system from a scale (30 oz in my case). If the high pressure port is closed (shrader open) Im actually...

I stripped off the bolt to the fan shroud bracket on my 2005. I'm thinking of welding the bracket to the engine. Does that look like an aluminum front bracket in front of the engine block? If it is I'm screwed as the bracket is steel. Does anyone know? And worst case, whats the harm in not...

ok I recently did a blend door install. Fixed the recirculation door problem but now the passenger side is blowing warm air that eventually gets a little cool. Driver side blows cool air from a Single Zone System. Before I take the hvac box apart again (and invest in a refrigerant re-capture...

This can only be the injector right? Either the tip or the solenoid.

ok installed this on sunday. I think its working. ACC on and the compressor fills the air tank. leave the key where it is for an hour and the compressor doesn't cycle so assuming no air leaks. pacbrake on, cold start: The pacbrake warm up feature activates. I can hear what sounds like quite a...

Hi folks I have this question out to pac brake. But if someone has experience i would appreciate some hints here. this screen shot is step 10 of the installation instructions for my 2005. You can see the steering column protector. It appears this connector is somewhere near the fuel filter...

Thought I would share what I learned. This video gives a good overview. However I have a 2005 auto,4x4 and so its a bit different. 2 things sort of hung me up for a bit. #1 the strap - I didn't see this until I pulled the dash back. I was pulling up and well it wasn't going anywhere...

Merry Xmas everyone! Was putting my dash back together after a blend door install and found this connector dangling. I didn't take it off so it fell off from somewhere on the drivers side. Any ideas?

Hi Everone Has anyone used this software on a 3rd Gen? Will it let me turn off individual injectors?

Thought I would post a pic of how I torqued my hub extenders down start by installing the lug nuts back on the hub extender then use a pry bar and a platform to hold the wheel in place Then a crow's foot and torque wrench to torque the nut to 95 ft lbs. I did 100.