Search Results for Query: *

Figured no one else would do it so I should roll up my sleeves and make a video. Hope y’all enjoy. Robert

So planning to swap the D350 with a 5600. The 518 has not impressed me. lol On my 4wd swapped trucks, I have used the speedo signal from the 205 as factory did. But the 2wd 5600 has no speed sensor to pull from and with no 205... Anyone know of a way to generate a speed signal for the speedo...

I have this 1993 D350 that I want to go through the front end. Ball joints are done already, but the steering idle arm is worn and figure after 30 years the tie rods, center link, and many other items should just be replaced if I am in there. What brand would you replace with? Looking at places...

Trying to find a clear answer on the difference between a 250 and 350 front Dana 60. Do I gather they are the same spindle to spindle, but it is the hub that is the difference? Reading on line has given me unclear answers. Where I am going is I have a 250 Dana 60F that was originally in the...

Looking for a very clean W250 or W350 Cummins club cab or even a crew cab if Cummins swapped. Can be auto or stick, but stick is preferred. Must be lower mileage. Distance is not an issue to come get it. Not looking for a restoration candidate this time. Please let me know if you have...

Y'all know I like my manual transmissions. But I ended up buying a 1993 D350 dually auto, that has 40k miles on it. It lived a harder life as a company truck, but on the overall it has survived well. Having an issue with the trans and looking for guidance. My solution for automatic problems...

Looking for guidance. I am aware front to rear gear ratios do not have to be 100% the same. Many new fords even come with a slight difference in ratio (example 4.10 to 4.11). The 90 has 3.08 axles. I want to stick a Dana 80 into the truck, but dont want to lose my lovely highway gears. And as...

The Ontario Chapter of the TDR will be touring the Ram assembly plant in Detroit Michigan on Tuesday June 11, 2019 on the way to Columbus Indiana for the National Rally. After the tour we will run a convoy of trucks to the event. We will spend a night en route at a pre booked hotel, and then...

Question for you 3rd gen gurus.... was there ever an exhaust made between 2004.5 and 2007 that didnt have any emissions **** in the pipe? I am not asking aftermarket, but Dodge factory. Maybe Mexico had no emissions?? Thanks! Robert

Sooo, years ago the crew cab got a PDR kit that has a HX35 and HT3B. Issue is, I dont have a down pipe. I called PDR and they were extremely rude and non helpful. Granted, I know Piers Harry isnt there anymore so the guy may not know.... Anyone know if there is anything that is available on...

Random question.... I may end up being in Texas towards the tail end of October with the the 1990. Question is, anyone know of anything first gen related happening in that time frame that would be worth planning into a trip? Any good boneyards 1st gen friendly? Anything of diesel interest...

So, the 1990 was spewing fuel out of the AFC vent. So I pulled the pump, and sent it to a very reputable shop in the area as he has been rebuilding these pumps for over 30 years. He flow tested the unit when he got it from me (23cc) and then replaced the all the seals as I didnt want to half ass...

Alright folks, I am getting this going 11 months early. But we all know some of us need some time to get our trucks road worthy. TDR goes back to CMEP (Cummins Midrange Engine Plant) in June 2019. Last time we had a reasonable amount of 1st gens show up. By reasonable I mean pathetic. This was...

So, the crew cab needs a sound pad for under the hood. Looking for a NOS one or extremely clean used one. Anyone have any idea where I should look? I am stumped on this one. I have not ever even seen one on Ebay. Any good NOS guys to look for that may carry them? Thanks. Robert

Software updates are a way of life.... but man do they suck. lol Where does one find: - Their user control panel - All of ones old posts Thanks. Robert

Just got my 2018 3500.... what should I know about it? So the 2018 3500 SRW 4x4 mega has arrived. Nice looking truck. Has the air ride, aisin, Laramie..... Coming from the 2008, this sure is a much nicer interior. No more rat fur grey. Next question: All trucks have quirks. So did the 2008...

Hey Guys, Looking at changing the 2008 Mega Cab up to a newer truck. This late 2000s emissions equipment is too troublesome. So a few questions and the reasons behind them. If you have any info, please help clarify these questions. I am looking at a 2017 or 2018 3500 Mega Cab dually. 1 - MPG...

Hey Folks, Had a small incident on the W350 crew cab this past weekend. The passenger side, rear door roll up window exploded. We are not fully sure what happened, but dad opened the rear passenger door and the glass literally shattered. There is nothing left of it. This is a look at the...

With the crew cab coming up on needing brakes, I have been looking at doing larger brakes and calipers. With these though, I need to modify the spindle bracket that holds the caliper but I dont want to modify the originals in the event my idea fails and I need to revert back to stock. Does...

Yes, our very own first gen mod Alan/Cerberusiam gets the limelight! Oo. Well done mad and great article. Reminds me of my early days here with Pastor Bob, Nascar Mark, etc. https://www.turbodieselregister.com/content/492-Thank-You-Alan-Rittberger Robert