Search Results for Query: *

Hello All, I need some advice. With the bombs listed in my signature, I am having some issues. First, way too much smoke. Second, EGT's will go way above 1500 deg if I bury the loud pedal. Third, the turbo surges badly unless I bury the loud pedal and keep the RPM's up. ( See...

Hello All, I haven't been on the forums in a while because I have been having a blast out driving my new :-laf 95 4X4 CTD. ( after the bombs it was a completely different truck. ) After logging some miles behind this monster I have a few questions. 1. With all the Bombs in my Signature...

Hello all, My truck is in the shop :-laf getting the following MODs. :D lets hear what you think the numbers will be when complete... 1995 4X4 auto 15. 5 deg Timing 191 DV's 370 injectors HTB2 64/14 Piers Exhaust Manifold ATS Stage IV with the Billet input shaft and flexplate...

Hello all, Today is your lucky day, or maybe I should say my lucky day. I am polling for advice. I have a 1995 2500 4X4 that is relatively stock. I am currently having a stage 5 ATS transmission installed and am now in the market for horsepower. My goal is 400 rwhp streetable truck that...

IS anyone running the Westach high output boost/EGT guage? Here is the story. I installed mine as per the intructions from Westach and Geno's. When I switched it on the Boost reads 4psi with power applied and the truck not running. I called Geno's, and they were very helpful. They said they had...

How do you keep the rain and stuff out when you are parked? Surely you guys aren't only driving when it is clear blue and 22 out. I was thinking of stacking my 95 but it rains here alot and I very seldom get to use the garage.

Hey, can anyone tell me where the drain-back valve is? Does the pump have to be removed to replace/repair it? My ruck is hard to start after sitting for a few hours :{ , but only if I park it nose up or level... :( If I get it even slightly nosedown, it starts like a champ. Even after...

how loose should the fuel heater element be once you remove the fuel strainer? I removed mine in my seemingly never-ending quest to cure my hard starting problem. The fuel heater element was loose when I went to replace the gasket on the bowl. I didn't tighten it at the time because I wasn't...

Does anyone know what the part number is for the AFC housing o-ring or gasket?? Also, is there a different parts source other than Cummins? (There isn't a cummins within a hundred miles of me... !!!) Perhaps Case?? Mine has leaked since I removed it to install the fuel plate. Also, Can...

Hello fellow oil burners... , I have a question reguarding transfer case chains. My 95 has the stock transfer case with 205,000 miles on it. I have alot of lost motion in the drive line, especially when I have to lift off the loud pedal quickly with the TC locked up. I went through the rear...

Ok, the #5 plate is in, and you guys were right. It works much better with the 160 pump than the #11. Here is the new question, Who has had experience installing a DTT valvebody. I don't have any good diesel shops near me, besides I enjoy doing the work myself. I just would rather know about any...

Ok, sounds like the #11 plate I put in my truck isn't giving me the power I want, so I an now considering changing to another plate. I currently have a DTT valvebody and Torque converter (89% I think. ) can anybody give me the approximate power numbers for a TST #4 plate? Will it work with...

Hello again fellow TDR bombers... :-laf I have the opportunity to get an HX-40 from an 8. 3 liter CTD for cheap. ( read FREE!!!) The catch is it needs to be rebuilt, which I can do no problem. The question is what benefits/tradeoffs am I going to experience from the stock HX-35? Also...

Hey gus I need a little help. I found the mystery switch instructions on the TST website and have a few questions. My 1995 was built in jan 95 and it doesn't appear to have a trans relay. the Power dist. Center fuse box lid has a legend and it doesn't have a trans relay listed. it has an...

Can anybody send me the diagram for installing the Mystery Switch on a 1995 4x4 with the stock transmission.

Hey guys, I just installed a #11 plate along with the westach bost/egt combo. Here are a couple of questions I have. 1. My boost guage always reads 4psi with the power applied. Can I adjust/calibrate it? 2. if not, does this mean I need to subtract the 4psi from the max boost to be accurate...

Hey Gurus, How about this one... I finally decided to change my valve cover gaskets after 202,000 miles or so because they had been weeping since about ... oh... 90,000 miles. I Climbed up into the engine compartment and spent the better part of an afternoon cleaning the heads then replacing...

Where can I get the sotheast KDP jig? I have made it 202k miles and really don't want to push it any further. by the way, I just installed the #11 plate from TST and am pretty happy with it. Just needs some fine tuning.

Where can I get the sotheast KDP jig? I have made it 202k miles and really don't want to push it any further. by the way, I just installed the #11 plate from TST and am pretty happy with it. Just needs some fine tuning.

Hello all, I am looking for an engine oil dipstick from a 94-96 ram CTD. The dealer ripoff artists want about 96 bucks for one. Anybody got any ideas?