Search Results for Query: *

The bottom of my oil cooler housing is leaking coolant, decided to go with a new Cummins housing and new valve and spring (oil cooler was replaced with a new Cummins unit a couple of years ago). I used Cummins gaskets at that time. Here is the question, watched a YouTube video on the tear down...

Been driving myself crazy looking for replacement light bulbs for my overhead trip computer back lights They are smaller that the AC/Heat controls backlight bulbs and not even close to dash light bulbs. Went the dealer, couldn't find them ,searched the internet no results, searched TDR posts...

Does anyone know where I can get some replacements of my Cummins super bee decal? These are faded out and the last time I bought them was at Thunder in Muncie diesel truck show. If you look, it's a Cummins turbo diesel engine with dual rear wheels

Since the 1970s I have had some form of a Cobra Classic CB in my cars and trucks. I got the great idea of upgrading to a Ham/CB and bought a Stryker 955HPC 10/12 meter radio (clip a jumper wire and get 11 Meter/CB bands). Problem is I want to see the display safely while driving and the Stryker...

Ok this is a new one for me. Started today, oil pressure at least 10 psi higher than ever before. Conditions, Outside temp in the morning startup 68 degrees, fleetguard oil filter, Rotella T6 15W40 (900 miles on oil change), Autometer mechanical oil pressure gauge. at startup idle 80psi (normal...

I have a "early" 2004 that has had a ton of modifications and would like to add a alarm to the truck. I have a factory smart key and remotes, but want break in alarm and tracking abilities. Truck has a manual transmission. 1st would like to keep the factory remotes. 2nd must have tracking. 3rd...

Just got done converting my truck from a 48re to a NV5600 and after reprogramming the ECM to a manual configuration the truck shows a P2127 code that will not reset. The truck was running just before with the automatic setup with the NV5600 in place an no codes. I have put in a new APPS setting...

After having and automatic for 9 years its time to dump it. In a diesel truck I am not compatible with an automatic. So I am going to swap out my 48re for a NV5600. Truck is a early 2004 and does not have all the computer stuff and emmisions 2004.5 and up has. The electrical has more in common...

I added a MM3 last month and have a few issues (referring to my truck ;) ). The motor power is awesome in sport mode it breaks the tires loose at a 30mph float, finally using all the toys I built into the Cummins with 8 years ago, see signature. Transmission has about 20K miles on a rebuild and...

My son's 2000 Dodge 2500 with auto just puked its VP44. Looking for a good rebuild, prefer local. We are in Ocala Florida, anybody Know a good place to get one? We will be replacing it, done it before on my old 2001 3500. I will also consider online too. Thanks Kyle

I was a big fan of Edge until today, apparently they were bought out by Holly and I have never been a fan of thier carbs. I was on the phone for hours trying to get some help pulling some more fuel fom the CTS. since I regeared from 4:10s to 3:73s it needs more fuel to get the turbo charger...

after 4 cardone rebuilds in 8 years, I need some reasonable priced alternitives. Looking at the Borgeson Gear box, Amazon has it for $625 shipped. has anyone installed one of these and do I need a new steering shaft? Thanks Kyle

I believe I had this happen before, No Park Mode, shifter has to be encouraged to park to get the key out. 2nd gear is nowhere to be found. I drove it home, run up the rpms some, back off the throttle and it jumps from 1st to third, everything else work fine including reverse, fluid is fine...

My Son's 2000 Dodge Ram 2500 just started leaking a lot of oil on the drives side of the motor, looks like its coming from behind the ECM, could it be the a head gasket? Doesnt seem to be mush else there that could leak oil. He just repaced the valve cover, changed oil, and put new water pump...

This one has me stumped, I decided to add a mechanical gauge to the truck and the original plan was to put a T in at the factory oil sending unit and add a mechanical gauge, low and behold Cummins uses a weird side end on its sending unit and I can't find the right plumbing parts. So, I decided...

Fits 1994 to 2005 Dodge Ram Cummins Turbo Diesel. Just Factory Rebuilt and tested and still in factory sealed packaging with gaskets. reason for rebuild, Airbox too restrictive and damaged the oil seal. Last picture is another one installed on a 2000 Dodge Cummins. Great turbo for towing and...

I not an expert to say the least on automatic Transmissions, but I need to leaned about the kick down settings. I done some readings on TDR about this topic only to confuse myself further. So here is what I am dealing with. A rebuilt and beefed up RE48 with about 60k miles. Transmission heater...

I am in the process in regearing my truck from 4:10 to 3:73 and decided to start from scratch. I found a bare housing, i already have the 3:73 set of gears and carrier that was out of a flipped truck with 20K miles. There is several different bearing suppliers from Timken (which is what Im used...

Looked everywhere to find an answer to this, no luck. Showing J1850 loss of abs. Speedo dead, abs light on, an red brake light on. On road heading for lake City FL Please post or call me at 864-828-0110 Thanks Kyle

My neighbor has a low mileage 1998 Ram 3500 Quad Cab and pulls a 14K lb 5th wheel and needs more power for the mountains, it is a 12 Valve Automatic 4X2 Dually with 4:10s that is bone stock. So what is a good build and keep it under $1000 that will not mess with the transmission, I have not...