Search Results for Query: *

RPMs slightly increases by 100/200 for a second or so, then back to whatever it was. 5-10 seconds later same thing. Seems more prevalent on level to incline. Only happens/notice when in OD. Last fall same thing and was told trans output speed sensor was most likely dirty, remove and clean. Did...

Driving around 45 with cruise set. Maintains speed on level and slight incline in roadway. When on a decline the speed drops a little but then continues to drop and the cruise doesn't pick up on it. If I hit resume it goes back to setting? Don't drive the truck but once a week nowadays but last...

Anyone have a lead on where to get these? For high pressure lines from injection pump to injectors. Little blue isolators that secure lines. Lost 3 or 4, would like to get all new ones. Thanks, Joe

Post fix edit: Problem figured out, read full to see what and what. https://www.turbodieselregister.com/media/1-stumble.6941/ Hope the above link works - a short video that shows what's going on. Sorry the video is not clocked correctly - don't hurt your neck;) Bit of info: Noticed this last...

Right side outer most joint (connected to hub) - I was giving all the zerks a few strokes of grease and the joint referenced wouldn't take any. I removed the zerk fitting, stuck it into the end of the gun and it is clear. Just because I installed a new zerk fitting - same thing. The joint is...

Seems like the fuel tank isn't venting. Every time I remove the cap, even after a 20 mile drive, I hear a sound of air going in. For sure not pressure coming out. Is the cap supposed to be vented, or is there a vent on the top of the fuel tank module? Truck in signature, note fuel system. Edit...

Truck in signature. Typical "Now WHAT?! Ran great last weekend..." NOTES (hopefully to reduce questions): 1- Walbro fuel pump 2- Big line kit 3- Pre-pump filter/screen 4- 2 Post pump filters = Fleetguard spin-ons, water separator, and fuel (forget numbers) 5- All filters changed 2 months ago. 6-...

Truck has been sitting perhaps a few weeks. A few times I started it just to move it maybe 20' or so. Anyhow today I decided it needed a little run. Started it up and let it run while I was doing a few things, maybe 10 minutes max. I get in and notice "Check Engine", now it started fine and...

Preface: 2nd performance trans in approx. 2/2021 (note info in signature). The 1st trans, DTT, lasted 2002 - 2021, roughly 110,000mi and was done by same builder as present trans. Anyhow, about a month or so after 2nd trans done it did a few 2nd gear starts. Oddly these happened after driving a...

I was able to acquire a bushing for the transfer case range selector rod - Lost the original as I was tidying up wires. I picked it up today and decided to install it after I was done I figured I'm on the ground anyway might as well take a look at the left frontend and see if there's anything...

Please recognize the link I've included is where I first started out with the subject/title here and I'm attempting with this new thread to streamline and remove some of the variables from the other "linked" thread...

SOLD! Pending transaction - as of 5/12/21 Just got a Fab Fours, I call it a "long leg-ed road rodent (deer) deflector", front bumper and am selling my original one. It has no dents, not tweaked, chrome is nice = not new but pretty darn good looking. There's one small screw hole above front...

Before I get started realize I'm not wanting to start a "Mine is better than..." thing here. Just searching for information. As title mentions I'm soon to be moving to Pocono Mountain area where the deer are a problem. I want to get a front bumper that'll help protect my front end from...

Please unlock... I'd like to update this and allow others to read/reply.

A bit of info first. In July this year I sent my Mach 5 injectors back to Don for a freshen up. Bought new from Don's (F1 Injection now FDI) years and at least 100k ago and truck was hazing more at idle than I liked, but otherwise running pretty good, so figured they needed a once over. In...

Guessing the sticks need to be gone thru, pop tested or whatever needs to be done? Not quite sure? So a brief: I've had them on since, forget when but they first went in date wise see signature for date with dyno 525hp/1000tq. I'm guessing mileage wise around 100k ago. Some time, probably a few...

Since my original post isn't open for replies figured I'd provide update. Rear kits were not listed, had to mike them and go thru several to get what I was able to make work... Front different story. NAPA part number 675-1246 for like 7 bucks. Didn't have to drill so bushings or pins would fit...

I'm not having any luck online (Goodmark, Keystone, LMC Truck) trying to find the panel needed to continue rust repairs. Looking for left side rocker to floor pan. As you lay under truck and look at the cab floor under the door opening, what I needs is where the cab floor drops to the rocker...

OK so I used to have a bunch of pictures on the TDR, recently I looked at my album (Emphasis on album = used to have several) which contained 2 pictures, which I deleted and now the album is gone and I cannot figure out how to create an album and add pictures to it. I looked for "TDR...

What's the best way to swap from Dino to Full Synthetic PWR Steering fluid? I'd prefer to not have to deal with potential air pockets in the braking assist system. Years back I did the "pull as much as you can out with a Turkey baster" method and fill with new, but I'd like to completely get...