Search Results for Query: *

I recently installed a 4" straight pipe system on my 2001. Are there any mufflers that I could install to make it sound more throaty(louder is ok, I'm old school).

I serviced my son's '21 truck yesterday including the CCV filter. He called me and said CEL came on. He had the code read and it was P051b. I reset service reminder for oil, fuel filters, CCV filter. It threw the code after he drove 50 miles.

Where can I find the TDR recommended specs. for 2nd Gen. 4wd truck alignment. I had mine done to published specs. a while back and the way the truck feels when I'm turning bothers me. It feels like the truck is fighting back during the turn. (either way)

So, I'm driving along and I hear a chime, look at the dash and there's a check gages light on. Look over and voltage gage in pegged at 8 volts, pulled over and turned off engine, popped the hood and belt is still on. restarted and after 10 seconds, gage back to 14 volts, drive 5 more miles and...

I Found gear lube dripped on floor under 4WD actuator on front axle. What's does it take to fix it.

Ole' Red Mare has 320k on the clock, time for new injectors. Do I have to change any associated parts or just order 6 injectors.

If I R&R my track bar, does it require a front end alignment too.

TDR issues #101-119, yours for the cost of shipping.

Clearing out some space. TDR issues 101-119, yours for the cost of shipping.

Engaged the cruise today and after about a minute the truck started losing about 5-10 mph, then surged to set speed. It did this intermittently until it scared me into turning it off. Any ideas where to start looking, it has electronic type APPS, fuel pressure is good.

How do you know when your injectors are worn to the point they need replacing.

Help out here guys. Got home and parked the truck and started unloading tools. As I walked by the front of the truck, I heard the sound of drops hitting the cardboard I put under engine area.(cardboard is to catch the 2 drops of oil that comes from extended breather hose daily) I looked under...

Going to rebuild my Dana 80 LSD clutch pack next week. Where can I find the bolt torque values for the bearing caps and etc. when I put it all back together.

I was going through some slick areas today and noticed that one rear wheel was spinning faster than the other one. (1 barely and the other fast) I normally have posi-trac when going thru mud and such. With 295K, do I have a LSD problem, I just noticed this issue today.

About time to replace my compressor. Tired of feeding it R-134 every couple weeks. Where do I look for a OEM replacement to buy??.

Developed a pin hole leak in my OEM Radiator today and want to look at my options. Does anybody sell a better than OEM radiator that will fit in the OEM hole and bolt up without any mods.

After taking out a few different sized animals, I decided to install a led bar in my brush guard. What's the easiest place to connect it to come on with the high beams

:--)Hey Guys, Driving along @65, up and down some small hills and all of a sudden it sounded like a playing card in the bike spokes was coming from under the truck. I pulled over thinking I might have hit and was dragging something but there was nothing. I got back in and started to take off...

I started having lack of braking issues on my 24' GN lately. So I checked the wiring and grounds, replaced my 14 yr. old controller with a Curt Tri-Flex and installed all new complete backing plates with little change in braking performance#@$%!. I have to turn the controller all the way up to...

I took my rotors in to be trued up after R&Ring my pads and the shop checked them and said they couldn't turn they would be below discard width. I looked up the starting size=1.500" and their discard size is 1.323". .067 wear didn't look like much based on the overall thickness of the disc. Cost...