Search Results for Query: *

From near as I can tell, it looks like the top radiator hose is about 2. 0 O. D and 1. 75 I. D. But what some at a local racing shop were surprised when I asked about stainless steel hose replacement was that the bottom hose appeared to be 2. 25 O. D. and 2. 0 I. D. They said that this was...

Where is the best place to buy aftermarket stainless steel braided hose kit for all the coolant lines for a 2001?

Does anyone have experience on just how many gallons it would take to change out all the radiator coolant? Does anyone know the best drain locations to remove all the coolant?

Is it compatible with Cummings rubber seals? Does anyone one have some good news reports after change over to NPG?

Is it compatible with Cummings rubber seals? Does anyone one have some good news reports after change over to NPG?

That way I could drive it up in the back pick up of my Dodge. The power to weight ratio is better than some Porches. A little convertible is exactly opposite a big Dodge 4x4. Could be a lot of fun hopped up. Another FAST AND FURIOUS craze.

I noticed how much cooler my exhaust temps were when it is raining and extra high humidity and then started thinking about what if I was to add a water mist system. Do people use them in competition during tractor pulls and drag racing or to clime a big hill with a heavy load?

It was raining today and noticed how much lower my exhaust temp was with the extra humidity. Is anyone out there using water injection combined with NOS and Propane during competition?

Has anyone relocating the AIT sensor to keep it from collecting carbon. I would be a lot easier to service some where else or would not require any service at all.

I have a Automatic trans that has been reworked by BD Power and was wondering how do I change the point where it shifts?

I have heard some one mention that there is a black box override for 24 Valve motors which will allow them to run into the 3400 rpm range. Anyone heard of this one?

I was wondering what people are using to balance their tires. I was concerned that Dynamic balancing only goes to 50-60mph. I think race cars use static balancing. Which is better?

I am looking into 2" spacers and need the correct dimensions. I also had some questions about whether It should be taper lug holes or not.

I was wondering with 3:54 what size tire would give me the same effect of changing my rear gears to 3:73's. I have an automatic and was wondering how to calculate.

I have a dually and wanted to run a wider tire in the front that has a little different diameter height than the rear. Is . 1" anything to worry about?

I have started looking into tires and treads. I like Toyo M55 spec. I noticed that they make a LT265/75R16 that is 10. 8 wide on a 7. 5 rim. Does anyone know were to buy 7. 5 steel rims to run this tire and keep the stock center caps and chrome. If not I guess I will be into aluminum rims for a...

I have started looking into tires and treads. I like Toyo M55 spec. I noticed that they make a LT265/75R16 that is 10. 8 wide on a 7. 5 rim. Does anyone know were to buy 7. 5 steel rims to run this tire and keep the stock center caps and chrome. If not I guess I will be into aluminum rims for a...

I was curious if anyone had success towing with DD Super Metals. With the extra power allow it to clime hills easier. I am sure it would take a HX-40, Camshaft, Ported head, 4-5" exhaust, Big Air filter and so on. Maybe with a TST Comp box you can turn it down a little. Any one set up like this...

2001 w/40K should I retorque head to 125ft/lbs? I am running a little propane and nitrous occasionally and have heard that cylinder head bolts could be torque to 120-125 ft/lbs to try and save the head gasket from blowing out. I know I really need an o-ringed cylinder head. I went to tighten...

In Muncie the black truck that turned 12. 4 in the 1/4 said that he was using a Mallory 4140 fuel pump and connecting directly to the existing fuel filter. Why are so many people trying to feed into the lift pump that has already proved to be a problem instead of by passing it? Who owned that...