Search Results for Query: *

Was wondering if anyone here has access to finding part numbers for the brake lines coming off the ABS unit. There are four lines that exit the unit. I went to the dealer here and they looked it up and said that there is only one part number for the bundle of lines exiting the unit. I had them...

Does anyone have any first hand experience replacing one of these? Researching the interweb you get different answers. Some say it needs to be programmed and some say it doesn’t.

Anyone here know if there is a difference between cranks for a factory spec auto truck versus a factory spec manual truck? I’ve gotten conflicting info via interweb searches and was hoping someone here would have first hand knowledge. The specific info I'm looking for is on the bolt flange on...

I’ve been getting this code randomly since the truck was new. I brought it to the dealer a couple times while still under warranty and they said there’s nothing wrong. I do have an aftermarket bumper, but I still got this code for 30K miles with the factory bumper installed. Any ideas where I...

We just finished swapping my sons ‘94 2500 from an auto to an NV5600. There are no ports in the trans for a temp sensor. If I drilled and tapped the fill plug, would that be too high up for the sensor? We will be adding two extra quarts of fluid and never plan on using the fill plug as we will...

I did a CP3 conversion on a ‘14 Duramax over the weekend. I drove the truck afterwards for about a half hour and turned it off, truck ran great. When I started it up, it was sputtering and would not move under its own power. I got a “change fuel filter” message on the dash. This was a brand new...

Will a Dana 80 rear axle out of a ‘95 bolt right up to an ‘02 that has a Dana 80? Both have 3.55 gears.

Does anyone know how to remove the front axle center shaft? I’m changing the gears in my truck and while I have the front end apart I’d like to change the bearing on the center shaft.

The time is getting close to where I’ll be needing to have my trans rebuilt. I’ve done a little research online, but that only goes so far. Opinions vary so badly that it’s hard to believe one way or the other. From what I’ve found, Superstick and CPP make some quality transmissions. Are there...

‘14 3500 SRW 4wd, can I run my truck at highway speeds with the front shaft removed? I removed the front shaft when I replaced my clutch and when I set it on the floor, a weight fell off. I drilled a hole thru the weight and plug welded it back on. I’d really like to get the shaft balanced...

My ‘14 has started leaking fuel from the electrical harness connector on the firewall side of the filter housing. It’s dripping out of the light blue connector. Any idea how to fix this?

I have a set of upper ball joints for sale, no lowers. These fit ‘03-‘20 2500/3500 4x4. Paid $500 new, make me an offer!!

I have a set of upper balls joints for sale, no lowers. These fit ‘03-‘20 2500/3500 4x4. Paid $500 new, make me an offer!!

I have a set of Carli 3” front coils for sale. These are new, never installed. Carli said they fit ‘03-‘09 2500/3500 4x4. Make an offer!!

2014 2500, truck is randomly puking out coolant. Trucks been doing this for about a year now, but recently gotten more frequent. We’ve changed the cap, heater core, water pump and two thermostats(just because). It does it randomly, no set pattern. Yesterday it idled for around 18 hours and drove...

Working down in Houma, LA right now and one of our trucks is 100% plugged. Wondering if anyone knows anyone in the area that is capable of doing a desoot on it. Dealer can’t get it in until next Monday, not too convenient when the truck is your hotel room. I posted here cause there’s more...

Does anyone know what these two features actually are/do? I was scrolling thru the scanner and came across these and both were disabled. I thought maybe the evr idle up was for the cruise control idle up feature so I enabled it, but no luck there.

So, drove the truck to the store this morning and shut it off. 10 minutes later, got back in and started the truck. The exhaust brake is stuck on and won’t turn off. I’m guessing my next move is to remove the actuator and see if the arm moves freely? I have no codes or warning lights.

I’m sure like many of you, bad things always happen when you’re nowhere near home. Coming out of the woods last night, 300 miles from home, I lost the internals from one cap on the rear most u joint. I removed the drive shaft and pressed out all three joints. From the looks of them, all three...

I recently changed my ball joints on my ‘14 and would like to say thank you to EMF for making a really nice product. I’ve replaced a lot of ball joints over the years and these seem to be above and beyond most others. I planned on doing a complete write up, but once I got started I totally...