Search Results for Query: *

Well I'm glad I'm not the only one. The steering wheel is pretty straight, so when I go to change the steering box I will cut some off. I will have to start researching steering boxes now. Thanks for all the replies.

The box always seem centered before. I went in the garage and turned both ways from center, just over 2 turns each way. Just make sure the steering wheel turns the same amount both ways right? The pitman arm was replaced by me and I'm positive it was in the same place. All parts seemed to all...

My steering box is shot, so I guess I'll wait until replacement to decide. I think it's weird I would have to reset coupler or pitman arm to get the adjustment needed. As far as I know everything is in it's original position. You would think other people would have the same problem if it is. Any...

The bars from the pitman arm to the tie rod. No lift.

I have had my HD T-steering on my truck for about three years. Right after I did it, I went and got an alignment on older tires. About a year later I put new tires on and noticed the steering wheel was off. I didn't mess with it for a long time. Today I went under the truck to fix the steering...

I will remove it, It was just a quick fix to see if it kept any fuses from blowing. I'm pretty sure it was an all black wire. I hope it's not a fluke that it went away after I taped the wire.

Well it must have been the exposed ground wire. Since I put electrical tape on it, I have had no more problems. Thanks for all the replies.

From the diagram I was looking at, it is a ground. The other side seems stock, I don't see anything similar. I just swapped the 20A horn fuse with the 20A Hazard fuse in the pdc. That fuse must have blown around the same time fuse 6 did I guess. Everything seems to finally be normal. I am going...

Ok, I will.

Where is the flasher relay? That's interesting because when Fuse 20 was blown, the abs and brake light on the dash were always on but would flash at times. I don't think those lights are supposed to flash at all right?

Ok, I took off the rear left tail light off and found a groundwire not attached to anything. Does anyone know where it should connect? I didn't see a ground screw or another wire it looked like it should attach to. I just put electrical tape on the wire and put it back together. I didn't have a...

Just an update. I found a 20A fuse and put it in the stop lamp. I started the truck and didn't touch anything. No abs and brake dash lights came on. So I moved the turn signal trying to get the fuse to blow and noticed no turn signal lights on the dash. I turned on the hazards and no hazard...

Ok. I just thought it was weird the dash lights would flash at all. I guess I will replace the multi function switch and see what happens. Thanks for the input.

It's not the actual brake lights that flash. The brake lights, turn signals, etc. don't work when the fuse blows. It's once I start the truck, the dash abs and dash brake light are on. Then I wait a couple of minutes and those same lights will flash on the dash, they seem to be in unison. They...

About two weeks ago I was driving home and noticed my dash abs light and brake light were on. I drove it home and discovered fuse 20/stop lamp fuse was blown. Everything worked fine until today when it did the same thing. I went to auto zone and bought two 20A fuses, I blew both of them in the...

So far the grinded down 90 degree ones are working great!

They don't make them for a 1997, at least not to my knowledge.

What year trucks can use that ball joint with the side entry? I wish they would make the upper like this carli lower ball joint. Dodge Ram Lower Ball Joints - Dodge Ram Suspension Extreme Duty System Components

I ended up grinding the 90 degree zerk. Main reason I did so is because when I tried to switch it to a straight zerk one of the ball joints was stripped at the fitting. I put some red loctite on it and stuck it back in. I did quite a bit of grinding so it gave me decent clearance. I didn't think...

Thanks I will try to find something to plug it tomorrow.