Search Results for Query: *

Best things I did for mine were 1- 3rd gen adjustable track bar 2- Top Gunz Customs tubular control arms 3- Steering Stabilizer 4- PSC steering box, cost more than any other but is not a rebuild. It is much larger due to larger sector shaft bearing and top bearing too. *Cannot be used with...

Wondering if CAD vs not has anything to do with 8800 gvw vs lighter version front workings?

Not sure what year this started = at 15mph (or was it 1500rpm) grid heater circuit disengages, at least that's what I remembered 99 doing. Obviously once engine up to temp they're not running.

My $0.02. From the first tire swap after I got my truck in 05/01 I ran 305/70/16s. When I purchased it it had 75,000 miles and came with Firestone 285s that had very good tread. Around 90k or so the track bar joint had play, I installed a new Moog, which I replaced in less than 8k and 12 months...

I installed the PSC box on mine years back. A tight fit between frame and block due to the box having larger bearings. One of the best improvements to steering I did along with tubular control arms and 3rd gen trackbar conversion.

My experience working with Geno's since mid 2001 is they vet what they consider offering before selling, provide great customer service and have no problem shipping out replacement items if damaged shipping. Highly recommended

I use hot shots secret additives. Was having intermittent fuel delivery problems. Removed walbro electric pusher and found a piece of bottle protective cover (aluminum) restricting pump inlet. Never know sometimes...

Around 10 years back I went with a PSC box as the original was leaking. I did have the steering stabilizer for many years prior. PSC box was notably larger than OEM due to larger bottom bearing and a top one. It came with spacers that had to be installed between the box and the frame due to...

If I'm remembering correctly, on my 99, same thing was happening probably more than 10 years back. Although it didn't make sense someone suggested cleaning the rear axle abs sensor. Doesn't take but a few minutes and if it doesn't work nothing lost.

Thanks. I'll take a look in the FSM. So, the "connection point" tells you where on the body/frame the ground is attached? I do have a test light and also a Fluke volt/ohm/amp meter. Just a whole lot confused with auto electric

I did look at wiring diagrams in FSM but also said it looks like Greek to me. Perhaps I missed something? Can you guide me to where it shows all grounds? As for fuel sending unit I did replace it sometime ago, forget when? At least it isn't the original.

Took truck out today for a 70 mile +/- round trip, 55 or so were highway at 65 mph. There were no RPM fluctuations cruise on or off. At the ½ point I fueled up. Get in start truck and fuel gauge is below E, just like when everything is off, all other gauges are fine. It was at 1 notch above E...

It is real = can hear and feel engine fluctuations. Thanks

Happened with cruise on "and" although I had to brake (disengaging cruise, but not physically turning cruise off = cruise light still on) to slow down for single lane for a few miles, as I steadied speed fluctuation continued. Understand this fluctuation, a bit hard to explain, is like driving...

Update The sensor wasn't really very dirty. It did have a very little bit of material see picture. I was surprised that such a small amount would cause the situation. I cleaned, reinstalled and went for a test run. Once on the highway the RPM fluctuations started again. I had to drive about 25...

Thanks John Probably 20 years ago I resolved the hunting situation which only happened around 40-45 depending on grade. Used the DTT filter and later did the wiring mod, just because. When (described in initial post) first happened my initial thoughts were TQ hunting. I read instructions for...

RPMs slightly increases by 100/200 for a second or so, then back to whatever it was. 5-10 seconds later same thing. Seems more prevalent on level to incline. Only happens/notice when in OD. Last fall same thing and was told trans output speed sensor was most likely dirty, remove and clean. Did...

Thanks Matt. If/when I get a day above freezing I hope to take a look at the vacuum lines.

Driving around 45 with cruise set. Maintains speed on level and slight incline in roadway. When on a decline the speed drops a little but then continues to drop and the cruise doesn't pick up on it. If I hit resume it goes back to setting? Don't drive the truck but once a week nowadays but last...