ecm

New again forum user here. My '01 2500 (HO 6 spd) ECM died about 18 months ago. Tried AutoECU for a repair and was unsuccessful, got a refund and sent it to Flagship1. I know. Who could possibly pick two shady companies in a row, but I did. After months the tracking number went active and...

Hello everyone, just joined here in hopes of finding a solution. I have a 2005 Ram 2500 cummins. I had some problems with the accelerator pedal ( response is way off and it feels like the truck is having a fuel cut ).. codes are: P2121 & P2128.. (other codes of wastegate solenoid and map sensor...

I'm pretty bad at diagnosing. I thought I had a bad alternator, and I replaced it to find it still won't charge, and my gauge on dash (that and fuel gauge are about only working gauges) shows it too. I don't know where to start. Circuits that control my AC blower, some gauges, power windows...

I recently sold my 2004 Dodge Ram 3500 CTD truck and have many accessories that were not traded out with it for sale: ARE or LEER Custom Topper, Full length glass sides with vent windows, Glass rear door, Carpet interior, Fishing rod holders, all clamps included, Molten Red color fits LONG BED...

OEM ECM replaced 2/2017 with a refurbished unit as a final troubleshooting effort to solve my BANKS tuner issues, no joy. OEM ECM resides in bubble wrap ever since. I'm in no hurry, but offering it up to gage any interest out there. If this is wrong approach to selling, I'm open to...

i am new to forum please advise or point me in the general direction of credible information regarding what all is required to perform correctly the upgrade from v10 to 5.9 cummins... as above my 1999 ram 2500 4x4 factory equipped with automatic trans and v10 engine..let go ! under extreme use @...

I took my 98.5 2500 out of the barn last weekend; I had a batteryminder on it all winter (Alabama winter). It started fine and drove away; after about 2 miles, the CEL light came on and now it won't go above 1400 rpm. It starts and idles fine. Codes: P1689 with the P1693 companion code. I...

Has anyone had an H&S Mini Maxx tuner take out the ECM? Had my 6.7 die in the campground after a 3 hour road trip and local shop says the Mini Maxx caused the failure. Truck has 179K on it, and last 40k have been with the H&S Min Maxx after the EGR/DPF delete, and no problems until now. Suggests...

Good afternoon! Are there any Techs out there that are familiar with the subject?. I've been dealing with the subject referenced codes for about 5 years now. All this time, I was pretty certain it was the TIPM, more than likely because of all the reports out there about problems some folks have...

I have an 01 24v just had the vp44 and lift pump replaced about 3500 miles ago, the vp44 was a rebuild from Thoroughbread and just a stock lift pump . It's now starting to take a few seconds to start, just when its hot outside (90F+). I have the edge CS2 to monitor fuel pressure and a few other...

Diagnostic computer still reports low voltage on my Crank Position sensor & code P0336. Plugs were exercised during ECM replacement. Thanks.

Pulling a load (7000 lb or so) and I think my transmission glitched. I think it took a moment to get into first gear when I started from a stop light. If it did, it was a very slight delay. Anyway, I get to my destination, unhook the trailer and my CEL comes on. At home I get my code reader and find...

I have a 2005 Ram 3500 Dually, 4 door, long bed, 2 WD, Stick, 5. 9 L, 102K miles. I am the original owner/driver and tow with the truck 50% of the time. The truck is stock and has been great! On my last trip was towing my equipment trailer and as soon as I got 100 miles into the trip I...

check engine light on no power, no 5 volt referance to the map sensor. question is can i a run a 5 volt reference wire to it and not the ecm. 2002 5. 9 ho thank you cjblaster