fass

I'm having a hard time finding info on fass filter replacements. It's a titanium model with XWS-3002 and PF-3001. What would be the Fleetguard replacement for this setup?

1999 2500 Quad Cab 4X4 auto with 4" exhaust, 189k miles, one rebuilt transmission, one VP44 replacement after OEM lift pump failure, FASS DRP-02 in 2010... I've been a DIYer on this truck and did a lot of stuff in hindsight I can't believe, because now-a-days I'm feeling pretty off my game and now we...

Had shop install a new FASS pump connected direct to battery for power, they disconnected and removed the block mounted lift pump and left connector dangling. Running great and after 4500 miles the engine light comes on. ECM code P0230 (Transfer Pump (Lift Pump) Circuit Out of Range). Mmmm...

I have four HF6604 filters for the FASS 95-150...I think I also have a WIX filter for the FASS I kept behind the seat as a spare on the road. The HF6604s ran $75 each from Fleetguard, I'll sell all for plus the Wix for $50 (plus shipping if needed). Located in Reading, PA.

To make matters more frustrating, this is the 4th visit to the repair shop in 4 weeks...arrrgh. NAPA is verifying if this may be replaced under warranty by "Carter". When asked if they should get one for me, I answered, "I'm not exactly sure I want this manuf. item." Thus my query, is there...

Hey there, long story short I have another thread about low power at 60 or uphill. Tested my fuel pressure and it was low. Found that the return line mustve had a hairline crack behind the injection pump, and that was only one of my 3 air leaks. I bit the bullet and got an Airdog 150 with the...

Any recommendations/guidance for location of the EDGE fuel pressure sensor? I'd like to put it on the VP44, but where? On the inlet side banjo, or on the check valve (return) side? I have a snubber from Geno's. I have the FASS Titanium, so the stock fuel filter canister is not an option. I've...

A little info on my set up: Truck: 2006 dodge ram 2500 Cummins Pump: Fass 95 series, serial number 3707 (now with the new style base plate) Filters: Baldwin BF1212 water separator (10micron), and a CAT 1R0750 fuel filter (2 micron). Ever since upgrading to a the newer style base plate...

I've had nothing but problems with my 200 GPH AirDog II. Just trying to buy the right thing involved 3 trips to Jefferson City so we've faced nothing but hassles from the start. Once we were finally on the road we barely made it from St. Louis to Salt Lake City and had to have a new AirDog...

Has anyone come up with a good way to remove (unscrew) the filters from a Fass 150 setup. I have a lot of difficulty getting the filters to release without crushing them. . Last time I tried this I had to take the whole assembly off the truck to get a good purchase on it. I am hoping someone has...

Hi, My 2004. 5 lift pump went bad at 123,000 miles. I've saved up for a lift pump/filter/air separator and want to know any pro/cons to the Fass and Airdog systems... Thanks in advance... Ed TavernierOo

So, I've had a FASS 95 installed on my truck for over a year now. It still has the original filter and separator on it with about 10000 miles racked up. My issue is the fuel pressure gauge originally started at 17-18 psi from the NPT fitting on the FASS pump and stayed put for a good chunk of...

So, I want to run the supply line from the fass, that would should be attached to the CP3 pump, to the intake port on the stock fuel filter instead. My concerns are fuel back flow through stock return, resistance going through stock filter, and which port is the correct one?!!? I would like to...

Hi, I have a 2001 24v truck with about 95K miles. Truck is essentially stock except for Fass 150/95 I added 1 1/2 year ago after the VP-44 ate itself. Learned a lot the hard way about limitations in stock lift-pumps and lack of stock fuel pressure gauges. At that time, I also installed the...

A few days ago my truck started skipping at moderate to about average throttle position (this is nothing new to us, we run WVO and we have become experts at diagnosing and changing clogged filters), so i took the truck as close back home before it would die and had my dad bring me out a "new"...