vp44

Need some help with this one. 2001 Ram 2500 5.9, 6 spd. Pulled engine to reseal, reainstalled and reconnected and had a crank, no start condition. rechecked all power and grounds and ended up adding only power and ground to the VP44 and it starts. Reinstalled all circuits to the VP44 one at a...

Is there any benefit to purchasing a Bosch reman VP44 vs. a reman VP44 from a reputable aftermarket builder? Does Bosch have access to better parts, electronics, and/or test equipment? Bosch reman pumps are slot more expensive than anyone else. Thanks

I took my 98.5 2500 out of the barn last weekend; I had a batteryminder on it all winter (Alabama winter). It started fine and drove away; after about 2 miles, the CEL light came on and now it won't go above 1400 rpm. It starts and idles fine. Codes: P1689 with the P1693 companion code. I...

Gentlemen: I need your insight and advice. My 1998.5 Dodge 2500 with 263,000 miles and nearly 21 year life (owned since new), has begun to start hard after it warns up. On initial start up, it fires right up after one tap of the starter. Drive it for a a bit, and it may take 5-10 seconds...

1998.5 24v, 250k miles, auto trans, edge comp box Couple months ago I was leaving a wedding an was showing off, got on it pretty hard then out of no where "check Engine" light came on an truck lost all power. Turned it off an restarted, it high rev'ed & idled higher than normal. Unplug the...

I have a 2001 dodge ram 2500 24 valve 5 speed, it has a new HO injection pump, and a new lift pump. Truck was idling fine than started to idle rough and quit. My toggle switch for my lift pump was on but now im getting no power to the lift pump.. Any ideas?

I'm new to the registry, but not to the cummins. I have a 2001 5.9l that is all stock at the moment with 253k miles. The problem I am having is that every now and then when I am leaving from a stop sign turning right, the engine stutters for a full second or little more. Once I straighten out...

I have an 01 24v just had the vp44 and lift pump replaced about 3500 miles ago, the vp44 was a rebuild from Thoroughbread and just a stock lift pump . It's now starting to take a few seconds to start, just when its hot outside (90F+). I have the edge CS2 to monitor fuel pressure and a few other...

Any recommendations/guidance for location of the EDGE fuel pressure sensor? I'd like to put it on the VP44, but where? On the inlet side banjo, or on the check valve (return) side? I have a snubber from Geno's. I have the FASS Titanium, so the stock fuel filter canister is not an option. I've...

Hello All, With the help of a friend we swapped my dead 99 injector pump with a donor from a 2001 ram. I was happy to hear the ole rusty Green Monster rumbling again after the 6 hour swap. It has been sidelined for almost 2 years... At startup, it was responsive to throttle and the rpm...

I was wondering what the best prices and places were to have a Bosch VP-44 injection pump rebuilt. Also, have any of you just replaced the pump seals and diaphragm? I have a kit that supposedly has a revised diaphragm which will not have as much of a problem with low pressure and will not...

Hello all, I have a 2001 Ram 2500 HO 6speed. The VP44 pump is dead and needs to be replaced. where is there a shop with good experience working on the vp44's? Near Lancaster PA.

Hello all, I've been digging through the forums for quite some time now (months) and am trying to hold on to hope that I am not in need of a new VP44. My truck runs great!! Just mounted a fuel gauge on it and it's reading 12psi idle and 8-10 psi wot (pre filter, oops - I'll be switching the...

Hello, I am a fairly new owner of a 2002 5. 9L Dodge Cummins 2500 4wd Automatic (4 gear) trans. The truck is fully stock and only has about 130000 mi on it. The lift pump and VP pump were said to have been replaced 50000 mi before I bought the truck and the trans was rebuilt right before I...

So I've had an occasional dead pedal, thrown a couple codes and suspect immenent VP44 Failure. FASS is fine according to guages, both permanent and a quick check at the pump to confirm my dash mount is reading correctly. The big question, is the Blue Chip Special X worth an extra $1,000...

My truck will throw the P02153(think thats right) injection pump/metering control failure code just about every time i start it up with a large percentage of vegetable oil in tank, but will not if running on mostly diesel, or mix. Should i be concerned or is this just the weaker combustibility...

Hey my vp44 on my 02 is goin out, im lookin in to buying the industrial injection hot rod pump package with the Fass 150. Is the inj pump actually mechanically different than stock?( springs, plungers etc. ) or does it have just a different driver module (electronics)? Kinda wondering if its...

O. k I along with many others have somewhat of an o. k understanding about the inner working portions of the VP44 Fuel injection pump either found in our trucks or on a bench at a dealer with a red inspection tag hanging off of it. There is a complex amout of circuitry within the pump that needs...