WOW ... We Wrenched, Wired , and Wooded

[ToolManTimTaylor]

An extremely Mini~Mini~Meet Went Well Mack Truck , Got a new Tailshaft Seal , TqT Got his trans somewhat straightened out (Now the driver(s) need foot adjustments) I TMTT CB'd and Tuned and Charged A/c . Wheatables Fondled his wood rails for refinishing. And TNTWay Blessed us all with Hornage!!



Thus another episode of a Mini~Meet comes to a Close.



CB Sends out STRONG ..... Real Strong ..... CoPhase baby!!





<hr>

Truck Bio:

Y2K+1 3500 4X4 Quad Cab 4:10:1 LSD



Somewhat Powerpacked By Bank's (4 inch exhaust,High ram intake,~Minus~wastgate mod to 38 psi,~Minus~ottomind TLC +guages,K&N) ,Blue Chip Premium FMC DTT~93%TC~&~VB~TC Smart controller, Mag-Hytec's Double Deep Trans pan,DD III injectors+Van Aken+Autometer Guages. ,Piers Modified PDR HX turbo,Enterprise Engine PerformancePusher pump setup Front End Leveling Kit from Jakit with 255/85R16 BFG http://www.bfgoodrichtires.com/ M/T's Custom Rhino Liner (see Tool Man's truck feature)DeeZee Black Diamond Plate Bed Rails And Tool Box , WAAG Side tubes with kick~outs Mopar Performance accessories-Sill plates-hitch cover-cargo aux lamp'n'Power, Hadley air systems 150 psi comp and air storage. DynaMat Sound deadening applied to entire cab and doors, Check out Tool's Stuff~>Here!<~

N. E. T. D. P

Three worded story ... ..... "over 1350 response posts - a new record!"

 

[TORQUE THIS]

Ah, yes, and then it continued at Dunkin Donuts

10 o'clock at nite





And there is an F-16 across from Home Depot in Startford, in McDonalds parking lot. There till 6pm tomorrow with real flight simulators



I know where I'm goin tomorrowOo. Oo. Oo.

 

[Mactruck]

Have to thank you Torque this for utilizing your shop while I made that seal repair and changed the Transfer case fluid. I have to say, even though it was a PITA to get the seal It hasn't leaked yet Oo.

I think the new new new updated seal has finally worked.

TMTT, I'll be posting a thread on the part numbers and such later today.

Special thanks to Snowman for giving me a hand.



Till next time

Kevin

 

[TORQUE THIS]

Kevin, thanks for coming down. Also, must thank snow man for all the adjustments and tweeks.



Planning on having a BBQ in July, maybe August. Chicken, burgers, dogs, clams, and whatever else can be put on a grill!!! There is a state park 5 minutes from my garage. Will put the boat in and have all the toys to play with. The park is usually filled up with (forgot, can't say it here). Well ya know what I mean, lets just say city folk. We'll see what happens.



The wife is due August 1st. Got that 2 week buffer before and after to deal with.

 

[bkrois]

It was a fun time even with a few people there. Now i just have to find a dodge to bomb. Special thanks to TORQUE THIS for hosting the wrench day, and for BigDaddy for the ride in his truck.



I'm up for another event, as i'm done with school june 17th.





It was nice meeting everyone who was there.



Bryan

 

[HoleshotHolset]

Mark said: "Chicken, burgers, dogs, clams, and whatever else can be put on a grill!!!"



How big is your grille?! *evil grin*



I'll bring some "BottleRockets"!!



Dennis Leary once said: "... . bring the whole #&$@# cow over here... I'll carve off what I want, and RIDE the rest home!"



Matt - a. k. a. "Bam-Bam", "BottleRocket", "You Idiot!" (that's Scott's favorite one... )

 

[stg2500]

TMTT,



Any pics of the new CB install? How did the mounts work?



Sounds like I missed a busy day of wrenching.

 

[ToolManTimTaylor]

Hmm Once my Cam is workin again i will

 

[Snow man]

TqT,thanks again for hosting the event,and your welcome. I hope it holds up til the good stuff goes in. Mactruck,your welcome,I hope you retightened those 8m caps. TNTway,you must be having fun with that little black box in the cab with 5 levels..... now that its hooked up all the way. I just got my DD pan today,if only i had it on sat. we could have made an even bigger mess!

 

[Mactruck]

Hey Toolman, The new part number for the output shaft seal is 5086054AA.



I posted my ordeal with part numbers Here and here.



See you at the next one

 

[Wheaties]

Hey Thanks TorqueThis!



... . I didn't even get sick this time! I was hoping to get a new coat of varnish on those rails before Muncie, but it ain't happening. Still, progress is progress. I'm glad to hear Kevin isn't leaking any more and it was great to hear TMTT over the air waves. When do you start your Diesel Hour?



Of course it was good to meet you Bryan and good to see the Snowman again... here it is June and he hasn't melted yet!



Matt

 

[ToolManTimTaylor]

Originally posted by Wheaties

good to see the Snowman again... here it is June and he hasn't melted yet!



Matt

:-laf :-laf :-laf :-laf :-laf :{ :{