1st Gen Misc. Parts for sale

[JDancoe]

I have a variety of 1 gen. parts which I need to get rid of. I would like to sell them to someone who could use them. If I don't sell them, they are going to salvage, so I can be very reasonable price-wise.

1992 Cab without doors, windshield or interior. Has sliding rear window.

1992 W-250 Frame and bed. Truck was hit in rear, bed has damage at lower corners and floor is buckled in right wheel well area. The frame is bent at the right rear wheel Kick-up area, due to being hit in the rear. There is no engine support crossmember, the front crossmember in photo is from a 2WD truck.

The axle under the rear is a Dana/Spicer 60 series - 4. 11 gears Non-L/S from a 1986 Dodge D-250, about 186K miles.

The axle in the bed is a 1992 Series 70- 3. 54 gears, Non-L/S, about 230K miles.

I also have a good 2piece driveshaft from a 1992 D-250 Diesel with Getrag Trans. and a 1 piece D/shaft from a 1986 D-250 5. 9L/360cid gas engine with 3spd Torqueflite.

Engine-trans adapter plate - 5. 9 diesel to auto trans.

Top cover and shift lever for a 1992 Getrag, and a good main shaft & countershaft for a Getrag trans from a 2WD trans.

Also have a dented short bed box for a 1984 W-150 pick-up.



If you might have use for any of these items, give me a call or e-mail me and let's talk. I can also e-mail you additional photos.

Jack Dancoe

Phone: 623-606-8941

E-mail: -- email address removed --

Located in South Fork, CO

 

[JMDancoe]

To anyone needing the parts that my brother has listed here: I am leaving his home in Colorado this coming Saturday. If, the fellow who wanted the rear axle in photo still would like it, I will drop it to you in Iowa and if anyone else in or near my route from here to Iowa and then south to Mississippi would like some of these parts, get in touch with him (my brother) and possibly I can drop them to you also. Saves freight money, guys. I hate to see them go to the scrap yard, if some of you need them. If you can help with "out of route fuel cost" that would be great.

 

[91W350]

Do you have any hubcaps? Looking for 16" beauty rings and one front, one rear cap for a 4x4.

 

[JMDancoe]

91W350: As of the moment, the only hubcaps (for 4X4) and beauty rings I have are on my truck. If I ever get a set of "Mag-Type" wheels for it, I may be interested in parting with mine. in my ramblings, I will keep my eyes open and if I can come across a set or even a couple, I will let you know. I like to drive, so I am considering trying to put together a sort of location service for TDR members, which may include pick up and delivery. If I decide to do this, I will let all of you know before my next tour. I dropped a rear axle (in picture) assembly in Iowa this trip. I do have a set of 1986 2 wheel caps, that won't go over the rear axle ends with the 70 series rear axle, which is in my truck. But no beauty rings for those.

 

[91W350]

I work in a recycling center, not many 1st Gen bodies come in, I keep hoping though! Thanks, Glen

 

[Big Red 94Ram]

Is that crossmember for an auto or 5spd? I need one for a 5spd. Should be the same part # for the 94's.



Thank you

 

[JMDancoe]

Is that crossmember for an auto or 5spd? I need one for a 5spd. Should be the same part # for the 94's.

Thank you

The crossmember my brother referred to in the add is one out of my 1986 360 gas motored truck which was an automatic and 2WD. It is the crossmember that sits right under the radiator. We bolted it in to make it easier to move the chassis around.
Jim Dancoe

 

[Big Red 94Ram]

Ahh, ok. I don't need that one. Thanks though.