Here I am

Recent Content by Ctallman

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff
  1. C

    factory door hinge install

    I just looked briefly at the hinges, they are getting really bad. I would like to get new everything from dodge. How hard are these to change? I noticed two bolts on each side going inside out. What does it take to get to these?
  2. C

    anyone running 315/75 tires?

    I just got a killer deal on a set of goodyear wrangler mtr's, they are 315/75's, and what i have on now are 305/70's. I dont have to lift the front end very high, i think a 4inch suspension lift might make these tires look small? Any other spring options? I had these ones re arched and a leaf...
  3. C

    good site for 4inch tailpipe?

    thinking about taking the stacks off, going to a tailpipe, anyone got a good website for 4 inch?
  4. C

    loose connection?

    thanks for the info, ill be checking the truck out tommorow
  5. C

    loose connection?

    As i was driving home from work the other day, i hit a bump and noticed it shut the engine off for acouple seconds, as well as the radio. I have checked all obvious wires, terminals, grounds. I even left it running and jiggled the wiring harnous and steering column but of course it wouldnt do...
  6. C

    Competition Ladder bars for first generation ext. cab??

    Can anyone tell me if anyone offers ladder bars for the first generation extended cabs? Or, do i have to drag welder out. All i could find were a set of traction bars, and they looked cheap and short. Thanks.
  7. C

    any first generation pullers out there?

    thanks for the info guys, what is a good set of injectors to upgade to? turbo?
  8. C

    Anyone make a pillar gauge pod for 1st gens?

    i picked my dual pod on the a-pillar up from summit.
  9. C

    any first generation pullers out there?

    what else can i do to my truck for alittle bit more snort? :p 93 cc 4x4, nv4500 sbc, open air intake, 4" from factory flange back, pod's, pump and timing mods, pdr hx-35, 3200gs
  10. C

    any first generation pullers out there?

    thanks for the input, i sure would like to drive it home
  11. C

    any first generation pullers out there?

    Ive been thinking about pulling at a local pull, and wondering what gear combo i should be thinking of. Last year the track was tight. I have fairly new maxxis bighorn's 305/75's, nv4500 sbc, pod's, PDR HX 35, BHAF, 3200gs, timing and fuel screw adjustments. 4'' exhaust from factory flange back.
  12. C

    No overdrive after sitting a year

    Ive recently got my 91 w250 out from the back 40 to take it for a spin. Its been sitting about a year and decides its not going to shift into overdrive anymore? Any info on the ol' automatic would be appreciated.
  13. C

    Shake, Rattle, and Roll

    Im asuming you checked u joints and carier bearing while checking the driveshaft isnt outta wack. Other than that ? Good luck
  14. C

    weird "dead rev"

    Hey i gotta dumb question. My truck has a weird sounding rev on top end. It runs fine untill i put it to the floor, then i rev's kinda steady, almost like my clutch is slipping, but still picks up speed and no burnt clutch smell. (south bend installed last fall) If im grabbing gears as fast as i...
  15. C

    piston lift pump

    Where can i get a piston lift pump from, mines starting to seep. Any good sites out there for performance parts for our trucks?
See more
Back
Top