Recent Content by SMcDougald

the marks are located on the bottom half of the linkage assembly. afteryoutake off the 8mm allen head screw and separate the top lever from the bottom lever (top attaches to throttle linkage and bottom is mounted on the pump) I will have to look at the pump some more. where exactly is the...

I have been using the Stanadyne Lubricity formula. It seems to be working fine. Ill let ya`ll know next month how it does on the mileage :-) When I went to go get parts for my pump at a certified Bosch repair shop They reccomended it to me... so we will see

See HHhuntitall I have looked for the manual shut off lever and i dont believe that mine has the lever. maybe it was messed with before i got it in 2007. And the reason for the Tach. is that i am not a trusting soul. I know the govenor inthe pump wont let it over rev but I worry about the...

sorry here was the picture that I tried to post in previous message showing my throttle linkage marks: DVolk, As you can see im not that brave either but i am taking (YAWN) baby steps. As said before "its a slippery slope" I had a `73 international scout II that I was going to keep...

ok so here is an update on the injection pump problem... after a LOT of reading on sevral forums and found out that it is a somewhat common thing. After taking the throttle lever off and removing the allen-head cap from the front of the AFC and working the fuel control pin in and out of its...

Greetings all, while trying to fix my windshield wiper arms (yet again) a friend that was helping broke one of the washer nozzles. Dodge dealer doesnt carry them any more and i am unable to find them at any of the 5 junkyards here in Mobile AL Does anyone have a part number and/or a place...

Am I correct that the AFC has a breather on it so it is dry. I'm getting around 12psi of fuel pressure to the pump. (Fuel gauge plumbed in after lift pump) the fuel filter is new I just put it in 2 weeks ago. Correct me if I'm wrong maybe someone that has done it can answer this. Doesn't the...

Boost gauge is reading about 2psi, fuel is showing 12 psi. But that is trying to drove over an overpass. Pedal to the floor truck is barely reaching 25 mph on the up hill side. I'm afraid to take it up a steep grade until I solve this issue. And I haven't installed a pyro gauge yet. But it was...

I also noticed that the wire going from the sir temp sensor to the pimp looks to be discolored between the resistor and the pump. Could the resistor have failed and damaged the wire in the process? Posted via Topify on Android

So I have been having lack of power issues with my truck for some time now. I can step on the accelerator and there is nothing there ( no guts at all) I can ease away from an interstcton and slowly build up speed but definitely no tire spinning power. I had major problems with my...

Ok so i was looking through JC whitney and i fell across this: http://www.jcwhitney.com/replacement-direct-fit-grille-assembly/p3038548.jcwx?skuId=1210132&filterid=d50224y1992g2j1 Its a shame that i dosen't have the "DODGE" lettering (yeah i know good luck) but i kinda like the all crome...

don't feel bad. I live over the line in Mobile and I have yet to see a member's truck. I saw a green 1st gen and that was what got me on this site to begin with.

I hate to feel like I am sounding dumb, but I have yet to find my voltage regulator in my 92 dodge. I have had a problem with my voltage staying around 12. 3 volts and after about 10 minutes of driving the "check engine" light coming on. I thought it was my alternator and just replaced the...

re: broken hub I don't know if it would matter but it is a Spicer 70 axle. aren't they all the same?

I was having ome work done on my `92 D250 2wd truck. The mechanic doing the work on the truck has been a Cummins mechanic for 30 years and has specalised in dodge since `90. He informed me today that the rear driver's side rear axle hub has cracked and needs to be replaced. HELP! Dodge dealer...