Search Results for Query: *

Wiredawg, do you happen to have the wiring diagram for the 7 pin? or a link with a diagram aka schematic.

Greetings All, Quick question, Do I need to wire my ole 1993 with the 4 pin first then get the 4 pin to 7 Pin adapter. Or can I wire the 7 pin. I got a 7 pin trailer and will need 7 pin. Finally, does anybody have a wiring diagram for me to use..... 4 pin or 7 pin. Any and all information...

Would you have a picture of this pop rivet installed???

on my 93 the masterlock would not fit. in fact I am having a hard time with a worm clamp......

Thank you so very much and being kind....intaglioed it yesterday and "mike drop" no more worries....I caught a another truck checking out my truck and I challenged them, ( gun in boot) and we talked a bit and he was looking for a tailgate.....told him he isn't getting mine......busted them, but...

David.....thanks so much, I guess I should have Googled You tube, I have a masters degree from You Tube University!!!!! I can thank you enough!!! and cant give you anymore likes, unless you reply back to this... :) BH

Thanks for the info David, would you be kind enough to post a picture of what yours looks like....I know I am a pain the butt for asking, but a pic is worth a 1000 words.....thank you very much BH

Greetings All, Hey does anybody have a easy trick, mod or something to prevent the tailgate from being stolen? Any and all information will be greatly appreciated. BH

Well it works for me....if you fill the bushing full of grease and try to put it on, then there is no place for the air and and extra grease to leave.....so you may not be putting enough grease in yours, but mine is topped off and I have no air and full of grease.... BTW the 1/18 hole is on the...

well, yes I did, the size of a small paper clip 1/16 or smaller, so the air and grease could escape when putting the bushings on the linkage. those bushing have no air and plenty of grease...

Thank you all fro the information, I did what y'all said and made sure they had grease, to get rid of the air and to easy the installation of the linkage i used a lighter to heat the tip of a paper clip and made a small hole at the top of the plastic bushings. Next Question Where Can I find a...

Greetings all, Hey I am having problems with the wiper arm busings, those white plastic pieces..it seem like once a year they break, so I am asking for any ideas on how to fix this problem. Are there some good ones out there instead of the cheap ones at Autozone or your fav part store. Any and...

Thanks again to everybody, I took the connection apart and everything looked ok to me. I have also read it is .050. FSM Should have had in there, but I concur its not in mine, unless I am looking in all the wrong places..... Now I put it the connector back together, and now I just must wait to...

BG Smith, You must be a mind reader, because that was next question, I looked thru the Service Manual for the location but it does not show it and does not have a install and removal procedure. Does anybody know if the procedure is in the Novel (Service Manual). I read somewhere that there I...

Ok, I will check the charging system, when the TACH is not working, I will check the battery voltage to see if the she is charging or not....now I must just wait for the problem to happen again. :) Thanks y'all for the information!

GrantP, Thanks for the info, I did check the OD when the tach was NOT working, and she would drop down a gear and when I turned the OD on, it would shift up. I also read about the CS Sensor could be bad, but I will check it out.

Greetings all, So my '93 Tach works intermittently and I can seem to find the problem. My symptoms are, (when the Tach is NOT working) 1. No Tach 2. No AC Compressor 2. low voltage on the voltage dash gauge. This will only last about 3 minutes or so, after driving all of the sudden the Tach and...

I though I saw some blank plastic connectors that where GM but looked as if it would fit, but Painless Wireing told me nope those wont work....go figure....Might just solder the wires to the ign swith then make my own connector with bailing wire and duct tape. hahahha...I will give the "mystery...

Thanks for looking BigPapa!!!!! I just shot Painless Wiring an email to see if they have one.

Greetings All. I am looking for a new connector/pigtail/harness for my ingnition switch. Does anybody know where I can get these items, just really need the plastic connector with some new crip on connectors, however a pig tail would work just fine or even a used harness that is good shape. Any...