Search Results for Query: *

Anyone got any good ideas on replacement hose for Amsoil bypass setup?gonna need a 7 ft section. Thanks to all I’ll be using Amsoil connectors

PM or email

Let me know what all you have and how much $$. Thanks Terry

Thank you sir.

What what do you have and how cheap.? PM details. Thanks or email

One basic question that I really should know. Does oil coming from engine exit the hole nearest edge of adapter and return oil via center hole of adapter? Thanks to all

I’m kinda doing this on limited budget so I’ll try by mounting filter assembly on passenger seat bolts. I replaced bolts with new ones about 3/4 in longer. Fabbed bracket there but gives me a hose run of 7 ft(2”)I located filter adapter that I think I used 20 yrs ago. All measurements are same...

I have 2001 Dodge Ram 3500 and plan to install a dual bypass system( full flow plus bypass filter under passenger seat area) I read somewhere Amsoil does not recommend dual type on Dodge diesel. Anyone with similar setup have any problems? I ran this on a 98 dodge for 100k miles with no...

I mentioned earlier I was looking for 1-14 thread.should be 1-16. Found Baldwin 5.5 inches 2 micron so should be ok

David, I have a dealer installed in tank pump with 100k miles on it. With Vulcan big line kit (1/2 inch). Goes from tank to vp44 and has 12 lbs at idle and 9at WOT.

You’re right. But where? I have seen several members with frame rail mounted setups but they must have used shorter filters. Thanks for comment.

I have added a fuel filter (spin on) cat 1r-0750 to my 2001 Dodge Ram 3500. I used the two seat bolts for drivers seat by replacing the bolts with longer and fabbed a bracket. Now filter is 7 inches long and extends down about 1 inch less than transmission crossmember bracket. Can’t find filter 2.0...

Thanks for pic and reply. Where exactly did you install? Can’t really tell from pic. Thanks again

I have 2001 Ram with dealer installed in tank lift pump. I plan to install fuel filter on or near frame rail and do away with 0EM filter. My truck is ‘stretch cab’, not full four door. Any suggestions on location? Have already installed Vulcan Performance 1/2 inch hose from tank to vp44. Thanks...

Could someone head me in right direction. I have 2001 ram 3500 with OEM fuel filter and want to relocate filter assembly using spin in filter that is easy to change. If that is possible. PM, post answer or email. I am getting on in years and OEM is a nightmare for me. Thanks much

My intank pump continues to work fine. Just made 2000 mile trip pulling 15k fiber to Oklahoma and back from Ga. however , I have bed off my truck preparing to install CM flatbed. My intank pump has a little over 100k but still holds 12 psi idle and 9 cruising. This is fine, but it is tempting...

That would be best , but might be overkill for my use. (770) for valve body !. More than TC! I used to tow RVs for hire to western Canada. Then, I had a Goerend full rebuild transmission and never a problem, now, I just want to tow a 10kfiftj wheel without worrying about transmission failure.

I'm gonna have Goerend TC installed and looking for a shift kit to go with it.( something to raise line pressure) any suggestions? This is for 2001 Dodge Ram diesel with moderate power enhancements. thanks to all for the help.

Evidently I wasn't very clear in original post. First, I installed a 'Vulcan big line kit' with 1/2 inch hose and proper fittings and discarded oem Bango fittings. Then, after a month or so, I installed 1/2" hose from quick connect fitting on top of tank to fuel filter cannister, using proper...

I have a 'snubber' connected to a 20" flex line that is connected to the vp44. Won't this be ok? I'm 77 yrs old so will prob outlast me. Yes, I'm sure the fuel pump setup is correct. I simply ran the 1/2" line from tank to fuel filter cannister. Works great! Even got a bump from 12 psi to 13 psi...