Search Results for Query: *

Good idea, thanks. Edge told me the connector on the Insight end is different on the CTS/CS units, but need to verify, and may be possible to swap-em out.

Edge supplied a custom one for the pillar install back in 2009, and no they don’t sell a replacement cable for my model Edge Insight (the original design), haven’t done a continuity check yet on the cable wires/contacts, but that’s next. Had to drive about 200miles today pulling a stock trailer...

Called Edge this morning, 10min wait for customer service. Problem possibly the unit itself or its custom OBD II cable that reaches up to the pillar mount, no repair service available on the unit, or even a replacement custom OBD II cable. They did offer a 40% discount on a new Insight CS and a...

Okay, thanks, don't typically let mine idle very long, so don't have experience with that on my rig.

soo....., hooked up a snapon diagnostic tool, and yes it it reads the two signals just fine, looks like a call to Edge is in order.

No OBD II signal for RGNfilter or the RGNfilter trg numbers on my Edge Insight, instead of a number, getting “N/A” for both. The trigger number of 5.9 (for NOx) is what normally is indicated, but as of yesterday just says “N/A”. Will unplug the Edge Insight, and plug in a diagnostic tool to...

idling with exhaust brake on or off? would think if it on, engine is working harder and so may create soot?

On further review of the forum, from Mullenax’s regeneration article and others, looks like the SOx regen takes place in the Catalytic chamber (and does need a high 1125F temp, ie-active regen mode to achieve it) and not a concern for plugging up the DPF. I’m going to quit worrying about it.

Have an EDGE – INSIGHT digital gauge indicating 7.6gm with a regen trigger point of 5.9gm. Yet there are no CEL’s or DTC’s. This seems weird, Is this a problem for plugging up the DPF? Does NOx/Sox regeneration take place in the DPF or elsewhere, like in the smaller Catalytic exhaust chamber...

Ditto what Jim W said, just lowered mine and repositioned it rearward, tho didn't think to go left also, good idea! BTW have been running mine this way for over a year, tire stays put.

Just saw this in the news today, another recall... . "Chrysler Group said it was conducting three recalls. The first covers about 22,000 Dodge Ram trucks from the 2008-2011 model years with steering problems. The second involves 65,000 2009 model year Dodge Journey SUVs to fix side air bags that...

RPalermo - my service manual (2009-3500) says ... . for the 2500 & 3500... "install the three mounting bolts, Tighten the mounting bolts to 196 N·m (145 ft. lbs. )". Would expect they are the same for your 2006. Hope this helps. Bruce.

Thanks for sharing, interesting, am thinking my first step will be to get the truck's current pre and post filter (stock 7micron) pressures measured with gauges, then measure again with the new Mopar 5 micron, and then proceed with the Fleetguard kit, so there will be a baseline to compare to...

Thanks. What did you install for your four fuel filters? I'm planning on installing this TRC-10 Fleetguard kit w/2micron filtration and separate water filter: Diesel fuel filtration systems Did you see significant drop in fuel pressure, post filtration, and have to upgrade your fuel pump...

Anyone know if my ’09 6. 7L has a lift pump fuel pressure sensor (after the fuel/water separator, not pre-filter) that can give a readout with an OBD tool? This would be handy, for monitoring the condition of the fuel filter, and for preventing damage to the high pressure injection pump. Or...

Just checked my ’09 3500, build date 11/27/2008, sure enough it has two of those “roll-over one way breather check valves” on top of the tank, one at each end. :eek: Thanks TDR, Fireman and others (and 10-9jc for the bump)!!!! :)

Mullenax - thanks for the feedback on the BK Flash! Haven't used up a tankful of fuel yet, but no issues, seems to run great, the overhead computer indicates mileage is about the same or a little better than before. Also, FYI, noticed, on my EDGE Insight gauge that the BK flash increased the...

MullenaxM – do you know what the Recall J35 Flash PN should be for my ’09 truck below? Took truck in to dealer today; technician said the truck’s ECM Flash suffix was AE, and the new J35 Flash he loaded up has a suffix of BK. Was sort of expecting a new suffix of A_ . Drove truck home (only...

EOwen - I have the same problem. My guess is atmospheric pressure is keeping the drain tube from draining until you loosen the threads enough to let a little air up past the threads to allow fuel to come out, but making a mess. Solution is to let your electric fuel lift pump create the internal...

Talked to Edge, in Utah, about the "Insight" and they say it does indicate "active regen. on/off". Ordering it today.