Here I am

xcellerator hot version installed

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff

posting video

Stanadynes fuel/water separator

Well i went to the mail box and saw it was in just like it was supposed to be and i programmed it all i can say is this box is amazing. If anyone was worried about the high hp claim don't be this thing is out of control sick and wrong. I smoke 2 times as much as with the six gun speedloader on 6 at least 2 times as much. It's almost too much power to even drive in town realistically with all the other mods i have. I'm thinking about taking it off the extreme setting while driving it normally. I was actually scared to put the banks on at all in the beginning. Then i finally manned up and put it to 4 and started running down trilby rd in ftc colorado. I was giving a ride to a guy who has done some work on my truck to get a second opinion and i was up to 80 mph in no time and here comes the sherrif right in front of me. what a bummer. i shut her down and waited but he never turned back thank god i've already been pulled over 2 times in the last 2 months luckily only 1 of these ended up in a ticket.



Anyway this program is awesome i can say that since i dealt with joe at pacific he has done nothing other than keep his word with everything. He told me i'd be impressed. I am. I also basically told him that if i was to buy it i wanted money back guarantee in writing if my dyno numbers weren't what i thought they should be for his claims. He took the challenge if u call it that. I haven't dyno'd yet but i can tell just driving it that they are gonna be a whole lot better. he said he was gonna over night it, and that's exactly what he did. i admit i was skeptical at first but if anyone has a doubt try it and see you won't be unhappy.



We are hoping to dyno tomorrow, hopefully me and lazr bob and mike. Now mike has tst comp box stacked with ez, so we will see exactly what he thinks of this when comparing it to that. I have ton's of before dyno sheets and i will take the following pulls and post them tomorrow if i can



1: xcellerator only

2" xcellerator and six gun on level 3

3: xcellerator and six gun on level 6 tried this for a sec today and no codeswere present. yyyyaaaaaaaaa



4. i will post the six gun on six with the xcellerator on the performance mode not the extreme mode.



If the dyno place let's us in tomorrow that is. I called today no answer and i will call tomorrow since it's basically a big party day i hope they don't close early.



hope this helps some people who are curious about this product
 
definitely the dyno numbers are the key i should be able like i said tomorrow but there was nobody answering today so then if i don't get it this weekend i'll make sure and go monday morning so that's the worst case scenario
 
well let me say again wow this thing is amazing i got brave enough and ventured to the tuff guy side enough to start applying the banks stuff over the top. On level 6 this thing was crazy fast i mean ridiculous and then it threw 2 codes. p033y crankshaft and also p0602 ecm comm error



funny enough another person on here just today has had a crankshaft sensor battle at hand and i've heard these things can be very bad if they break off or whatever so what to do i wonder i was kind of hoping that it was just the banks telling my truck to defuel at 1150 which it does, but it's not very good at it. it's seen 1600 with just the banks so it's lacking a bit i would say. I did get it up to like 1500 within seconds maybe 3 maybe hard to say but i was wondering if that could possibly in some way cause a code like this. I will call the people at pacific performance and also at banks tomorrow and see what i can find out



besides that the truck ran good after clearing the codes i even turned it back up to 4 and got on her good seemed fine. I didn't hear anything bouncing around or making any type of destructive sounds so hopefully it's just a communication error
 
The crankshaft sensor code is a code that is sometimes set by boxes that do timing and duration. The 602 is one that has been set by downloaders. I wouldn't worry about either one
 
sigh... ... ... ... man i hope u are right i was reading about that work that the other folks had to do and man was it sounding like trouble and downright conspiracy of dodge against me. No seriously though i was worried when i read that. then we began to think about the issue. I cleared the codes. the truck ran fine after that even while hammering it to the floor with the banks also on 4 and the xcel on extreme. now i also didn't hear any sounds of breaking or broken parts not one knock or nothing of that nature and i'm gonna call that pacific guys here in like 3 hours and i'm gonna call the banks folks too. I can't have this kinda of thing happening not after i finally got it. Oh yeah did i mention that this programmer is sick and wrong. In a good way this thing is off the map. I have only raced one truck with tst box. today dyno'ing should be all systems go as long as the code is no big deal. i have a chance to see what a edge, tst pmcr box, and dtt transmission will do. and in turn it's an ats lvl5, six gun speedloader, xcellerator, 100 hp injectors. He doens't have injectors. but he has 5" all the way through i have only 4. I have the killerb2 which he also had but you know what he did he went and got a sled puller 66 what a dog. that's why i went and got xcell. Not really i was hoping to get the jump on him i see that he think along my lines too. we both also have fass plumbed straight to the tank
 
ok so the dyno closes at 3:30 mst and that's too early for bob and probably too early for mike, so i'm gonna go it alone as usual. I told them about this chip and they were excited almost as much as i am i can't wait i'm gonna have the numbers today for sure it's just a matter of getting them posted and i'm still waiting to speak to joe about the code issue that was thrown and so on and so forth
 
dude you aren't even gonna believe this it couldn't ever happen to anyone other than me. Two weeks ago on the dyno jet at redline it froze up and stuck the break on he needed a new circuit board for his dyno i believe it's still down and out. Guess what happened today first run thing jammed up at 2000 rpm we were at 422 and 1009 or something and i still had 1000 rpm to go so that's the extent and i got it all on camera even the guy offering me a free dyno when they finally fix it. The same exact problem i mean what are the odds of that . Million to one or even great i would say. i was so ****** i called lazr bob and told him right away of the bad news since we were talking about making it a small group gathering. Man i'm disgusted it makes me so damn sick to my stomache. I was all ready had the camera and i had the time slot and i had the programmer and the truck running good. All for nothing man there is 2 dyno's in laramie county both dyno jets and both getting broken while i'm on them i mean i wish the karma god would get off of me before i drive this truck into a lake. i'm so ****** off and the only other dyno around anywhere near is at ats who is moving right now so it's not functional what a damn joke. i was ready to post results and it makes me furious, no irate, to think that i was going to stand behind this item which i took a chance on and then have the sweet opportunity to test the results and ;post them all for nothing... ... . i'm so mad right now. ... ... . well look for anyone who doubts the program straight up don't do it because it's bad to the bone. I will be sure to post results it's just gonna take a bit longer now sorry... ..... i mean the product was everything joe said it was to be and i mean i know i don't have the sheets today but i will try to post the video of the first run that i did get on the web page along with the pics that i have. However i hope for the guys at pacific someone can dyno this product because it's what it says they are selling a good product and i wish i could have done them justice today. I will get the sheets and i will post them it's just a short time but it's like forever. I won't steer u wrong though if anyone has any doubts just check it out he'll back it in writing and guarantee big power he said like 190 or something at the wheels and i believe it has every bit of that no joke or no lie. However for those who are really cautious just wait and i should have them sometime next week i hope
 
Hey, Moolie

There is a dyno jet dyno down here in denver called Dyno Pro off 52nd and Tenneyson that gets numbers the same as PFI does. I have ran on both dynos and got very similar numbers. Come on down and hit this one. They did a dyno day for the ford club and us so I know they know what they are doing. I'm sure Laser Bob has told you about my truck, so you should know I know what I am talking about.



Mike L.
 
Matt,



Just have a cold iced tea and chill out for a while. That horsepower won't evaporate. It will still be there in 2005. We can still get on a dyno somewhere. There will be a new one here in Greeley in a short time. It is in the ground already. It is not completely hooked up yet. Soon, though. I haven't heard what he will charge for runs for us.



Oh yea, spell my name "LaserBob" if you would.



Have a happy and safe new years eve.
 
ok sir u got it sorry for that i thought i saw one on here as lazr is all so maybe i saw someone else using that name but don't worry it's laser form now on
 
I really hope it works out for you. Can't wait to see your results also. However, I just spent a couple of hours over at "The Diesel Place" reading about the chevy guys experiences with the X-celerator and PPE in general. REALLY NOT GOOD! If you guys want some good reading go to the "The Diesel Place" and do some reading for yourself. To search you have to sign up but you can probably find enough without even doing a search.



Just an FYI...



Richard
 
well see i'm hoping to screen out all of those negative effects and basically i ordered the box with just the good qualities. U have to be sure and specify... ... . lol no way just kidding let's see i've had it for 2 days and i threw 2 codes of course that was with 3 chips, or 2 chips and a tuner. I also noticed mr. bob that my fass began surging again no way ahaaaaaaaaaaaahhhhhhhhh. It was a terrible sight for sure i think i'm gonna take it off of extreme mode just because it's a pain to drive it around town with that thing like that it's almost unrealistic. i realize how much i miss the 6 gun in cab adjustable feature

that's why if i turn it to just performance on the programmer then i hope to add the banks stuff with the 6 level being safe to operate on
 
Moolie or is it Gristle Missile------------Why did they ban you over on DTR..... seems like you were talking about the same stuff over there as you are here and you posted the dyno runs on DTR???????



Jim
 
Moolie,did you you use the speed gov removal part of it?I got a new quad box and was told it had this feature but could not find how to use it.
 
i wasn't told about any speed governer removal feature so i can't help u there. Yeah i got sick of dtr because over there no matter what u do there is always someone to say it's untrue or you lied or something so i' can't hang with that no more. Mr ellis had told me i was under 30 day mute for an arguement i didn't even start and i didn't use any obscene language or anything. so being the guy i am i told him that he was nothing more than a tdr wanna be and he could keep his white trash forum, with his one sided rules. I don't think he cared for that too much
 
not sure yet i'm gonna call them and see what the deal is i don't even know if it's fixed yet but i'll find out i'm calling them now
 
Back
Top