Here I am

Recent Content by alleyoop

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff
  1. A

    Mobil 1 Truck / Suv oil

    I used to get the Mobil 1 trk/suv oil at Walmart... Cheap price for the 5 qt. jug... But now I have been to at least 10 Walmarts in Cal. Az. , and no more stock. ? One manager says there not getting it anymore and he don't know why. Anybody know whats the deal ? :{
  2. A

    Headlight flicker...low beam to fog lamps

    I got the same problem... . what did you do to fix it ? :confused:
  3. A

    Head light / Fog light freaking out

    Monday mourning Started the truck at 1 am with 36 degree temp outside and warmed it up until grid heater stopped cycling. Turned on headlights and proceeded on my way... . after 50 ft. of driving the headlights started to alternate between headlights and fog lights. :eek: Then I clicked the...
  4. A

    Valve cover leak

    Mine leaked in the back . It was slow, but at 30k I had the dealer change the lower gasket..... the upper did not leak. :D
  5. A

    Pics of Fender Flares Anyone???

    Trying to add photo... ... :D
  6. A

    Pics of Fender Flares Anyone???

    Here's my Bushwacker Extend-a-fenders. I left um black... ... looks better like that to me. :D
  7. A

    Bushwacker fender flares?

    I put on the Bushwacker Extend a fenders ... ... fronts went on fine after re-locating Cummins emblem, back flares needed alittle fixin with a file so the holes would line up with fender holes... ... ... I did this so there would not be a preloaded . I will add flaps later. :D
  8. A

    Any good 17" aftermarket wheels for my truck

    Im trying to add a photo of my wheels to this reply..... Black 17" daytona wheels by Allied... ... ... . I left off the chrome center caps.
  9. A

    Removing Cummins badging?

    I used a heat gun and fishing line... ... worked great, then used wax and grease remover for the residue. Then I added some doulble back tape and re-installed them above the door emblems. ... ... ... :p
  10. A

    Grill Guards?

    I got a Southwest fabricators front and rear bumper replacement..... took off the stockers. New ones made in Texas, shipped to So. Cal... ... total was $1276 They bolted up to existing holes using existing hardware. :D See my readers rig's photo's
  11. A

    Aftermarket Front Bumper

    I installed a Southwest Fabricators front and rear bumper after looking at all the different styles and prices... ..... I wanted to stay under $ 1500... ... ..... these two were $ 1276 total dilivered to S. Cal. The front has the winch mount, original fog light mounts, holes drilled for factory...
  12. A

    315's how much do the throw my gas mileage comp off?

    Hi ... . I'm new to the TDR , and its Great ! I took off the stock aluminum 17's with 265/70's and installed some Pro comp 33/12. 50-17's { 305's} on black allied wheels... ... and my speedo was off. I check the internet and found 3 sites for tire calculations..... 2 of which came out the same...
  13. A

    Body side molding

    I got some of those factory black mouldings from a guy on Ebay... ... . they were $ 100. Also got an extra set of rear door mouldings for $48 for the bed section just aft of the rear door. I have a long bed and they look good on it. :D --------------- 03 ram 4x4 quad cab long bed
  14. A

    Checking Diff Lube

    A 3/8" rachet will work. If you have the 10. 5 rear axle, level will be 3/4" below fill hole +or- 1/4" . Mine was 1" below hole, so I topped it off with some Mobil 1 synthetic gear oil... ..... Its alot cheaper than the dealer synthetic. :D 2003 Ram 2500, qaud, 4x4... ... ... got it July 03
See more
Back
Top