Here I am

Recent Content by Clarkoh

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff
  1. C

    2nd generation intercooler

    Thanks I will do that. :D :D
  2. C

    Lifting a 2WD?

    19.5's This is interesting. I got excited about the thought of tires that would haul the weight and last forever. Got a set of 19. 5 wheels and some 225-70 19. 5 tires. So far I have not tried new tires. Got a deal on about 11- 19. 5's and am using them up first. Because they were used...
  3. C

    injection pump timing

    I LIKE the results She snaps to in the morning. Barely rotates and it is running, exhaust is clean as a whistle and it has more response. Have not checked economy accurately, yet. But it seems to be better on fuel. New injectors are right around the corner. BTW, when I used the BFB, the...
  4. C

    2nd generation intercooler

    What was your choice for new improved injectors?? How big is too big? I have been advised that POD's are too much, especially for pulling my big trailer. What was your choice?:confused: Anybody have advise?
  5. C

    Axle vent/seal replacement...

    Carb cleaner?? I used a scriber to clean the fitting on the housing. Most of the crud was jammed in there. A little carb cleaner and a bottle brush should do the trick on the hose. ;)
  6. C

    injection pump timing

    BFB Works too! I got 'er all loosened up and used a Big F'in Bar to exert some Brute Force. An extra hand from my son exerting pressure on the BFB, while I tightened the nuts kept the advance, advanced! Snapon's SP144 wrench is great for those hard to reach/see/ loosen nuts!:D
  7. C

    Throttle position sensor

    TPS Adjustment I bought my '92 new. From the minute I drove it I was unhappy with the constant downshifting from OD to 3rd with even the slightest additional throttle pressure. A friend at the Dodge dealer ordered a new TPS. We changed it and adjusted it by the book. Same old!:rolleyes: I...
  8. C

    red valve covers

    Powdercoating? If you want a great looking, durable finish, find a powdercoating place. Most have a plethora of colors available and should be able to hook you up. they usually sand or bead blast the metal, so the powder sticks to it. You can use paint stripper prior to painting or dropping off...
  9. C

    Aftermarket Cross Flow Radiator

    will a 92 fit? I just got a replacement for my 92. It is and was a cross flow? NAPA hooked me up for a reasonable price, around $200, I think. Direct replacement & the temperaure gauge has responded affirmatively to the fresh fins and tubes!! :D
  10. C

    2nd generation intercooler

    Great information Worth bringing back to the top of the forum! :)
  11. C

    Intercooler replacement

    2nd GEN Fits?? Has anyone done that? Used a second gen intercooler on a first gen truck?? :confused: Any suggestions for a good transmission cooler to replace my leaker? :confused:
  12. C

    How do you time an injector pump?

    Bought the wrench Ordered the SP144! Pricey little bugger $37. 88 with tax and shipping!!! :mad: But now i can make adjustments much easier!! Thanks for the tip! :)
  13. C

    Intercooler replacement

    Cooler = Better Whenever you compress a gas, it gets hotter or has more energy making the molecules bang into eachother. Like what makes a diesel, diesel. Compression = super heated air. This is good to a point, but if the temperature gets too high, things melt. Cooler denser air makes much...
  14. C

    Intercooler replacement

    Yes They are! I do not remember the price. I asked when I got my exhaust, gauges and K&N. It was pretty high dollar. :--)
  15. C

    How do you time an injector pump?

    THANKS This place is the best. And so are the participants! I could probably modify a wrench. Have torch, will bend!:)
See more
Back
Top