Here I am

Recent Content by JeffKing

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff
  1. J

    Drive Shaft Center Support Bearing?

    For the 2005 it is 85 foot-lbs Manual says to use new bolts. If you re-use the old ones you will need to clean off the old Loctite and add some Loctite 242. I googled Loctite 242 and it appears to be the BLUE Loctite.
  2. J

    New SW on Mads Site

    Marco, Thanks for your reply. I only run Smarty SW#1 or SW#3 and that is my only mod. So I am guessing that I will not see numbers much over 35 psi with the stock turbo. Jeff
  3. J

    New SW on Mads Site

    Marco, What are your thoughts on running the SW ... B with a stock turbo? What are the chances of killing the stock turbo? Jeff
  4. J

    New SW on Mads Site

    I see it now. For some reason my browser was loading an old page. Thanks Guys.
  5. J

    New SW on Mads Site

    Bob & JCasper, I have the s-04 smarty. When I go to the downloads page I do not see a 1. 11A, 2. 11A, or 3. 11A software for stock injectors and stock turbo excluding the WILD tm (4. 11A). I only see software version 1. 09A, 2. 09A, and 3. 09A for the stock injectors and stock turbo.
  6. J

    New SW on Mads Site

    JCasper, That is the correct location for the download but the software is version 2. 09. The new software is 2. 11.
  7. J

    New SW on Mads Site

    Bob, Will there be a stock injector, stock turbo release for this new SW?
  8. J

    Just tried the newest Smarty Beta

    The Beta 4. x really cleans up the smoke. Tried it out on the way home today and only say a light haze with SW#3. It also feels more responsive than the previous without the go peddle being extremely touchy.
  9. J

    Latest Smary Update

    Bob, I noticed that the Smary software for the non-06 version was up to 208A. What is the change from 207A to 208A? I would like to know before I update my Smarty. The link on the Smarty site is also kind of funny. If you click on the right end of the link you can get the 207A file and...
  10. J

    Average MPH (This should be fun!)

    MA2LA, your average is 13. 3 MPH not 40. 33,646 mile @ 926 hours = 36. 3 MPH for me.
  11. J

    Smarty Dyno Numbers/Graph

    Marco, can you post the dyno graphs for the original Smarty runs that you did to determine the HP gains?
  12. J

    Smarty CR software updates

    I have run the stock TM on level #3 and the throttle response is similar to stock but when you put your foot in it she takes off. I will be using the middle TM setting with #3 tonight after work.
  13. J

    Smarty CR software updates

    Thanks Marco, I am looking for the software that will provide the theoretical 'best' economy. Does the modified TM decrease the amount of low boost fueling and theoretically increase the milage at low RPMs? Thanks.
  14. J

    Smarty CR software updates

    Marco, the 302 update . zip file is corrupt. I have tried downloading it four times and each time it is identified as corrupt.
  15. J

    Smarty CR software updates

    I have tried all three update in the following order 202, 102, and 302. I get the internal error 2 for all three updates. First thing I did was load the STOCK program back on my truck and then I updated the smarty box and now non of the software updates work.
Back
Top