Search Results for Query: *

Cummins12V98 - Thanks for your response and noted on the AISIN and air ride. I actually have air-bags / on -board compressor on my current truck and use it all the time. So will make sure and add air in the event I find a truck off the lot that doesnt have that option. EZeis - Thanks for...

Brethren Its been a long time since I have been on the forum. Glad to see the RAM religion is still in place. That being said I am considering replacing my ole truck (2006 3500 Mega Cab 4x4) and could use some counseling as this is a tough decision. Obviously my truck is paid for and for...

Bob4x4 ... ... ..... you do good work!!! ;-) I just found the TSB and it appears to be the fix / answer to our issue. Guess I will try clearing the code and see if that will work for a while... ... if not then will run it by the dealer and have them update. Thanks again for the information...

Badboy- I replaced my drive-shaft years ago and can tell you its one of the best mods I have ever done on my truck!!!! Note: My truck is exactly like yours. As far as the part number is concerned I will verify tonight when I get home and post it. And yes when you purchase it ... ... ... . it...

Brethren- KRstone I hope you dont mind but wanted to jump in on this one. I too have a 2006 that is giving me the same code (2609). The batteries are a year old and have clean terminals..... and the cables are tight. I also had the heater grid relay replaced last year ... ... all connections...

Brethren- Sorry for the delay... ... . been on the road and just getting back to the forum. That being said I wanted to thank everyone for your responses. All very good points... ... . unfortunately I am still on the fence! ;-) My fear is that if I went with the AE version the difference...

Curse of the 06!! I have the same issues with mine!! Mwilson... ... ... ... . thanks for the link!!!! Southbound

Jumping on this train!!! And will be taking notice the next time I service my truck. Southbound

Brethren- I am hoping to get some feedback for those of you who have switched from the earlier version of the G56 (AD) to an (AE)? I currently have 156K on my stock clutch (I am knocking on wood as I type) and so far no issues. And yes I pull with my truck often!!! I am one of the lucky...

Correction above: The mechanic told me that there HAS NOT been any cases of tie-rod breaks while in transit. Also Note: Since my repair 2 of my buddies who have 2010 trucks have had the same break however when it occured the tie-rod damaged the rotor. Not good!! Take the time to get this...

Brethren- I just recently went through this... so wanted to share!!! I had my front-end upgraded about 2 years ago to the "latest and greatest". From what I have been told the original Recall was H46. Since I had the upgrade installed I have put around 50k miles on it. So... . just last...

CBowden- Not sure what the status is with your drive shaft but wanted to give you my . 02. So I have an 06 Mega which came with the two-piece drive shaft. After some research in TDR I was able to obtain the Dodge part number for the one-piece. Note: I think in 2007 or 2007. 5 Dodge changed...

TPasquali- You should check the over-flow hose which connect to the radiator right under the cap. Everyone of my buddies who had a leak... ... . turned out to be at this location. Apparently Dodge is too cheap to put a band clamp on this hose and so everytime you service the air-filter you...

CTRice- I too have an 06 and had a similar problem..... however my "neutral" light would stay on 100% of the time. Note: The 4x4 system worked perfectly but the light indicator did not. Dealer said it was a bad switch module (on the panel) which they replaced under warranty. Had I not had...

CTRice- I too have an 06 and had a similar problem..... however my "neutral" light would stay on 100% of the time. Note: The 4x4 system worked perfectly but the light indicator did not. Dealer said it was a bad switch module (on the panel) which they replaced under warranty. Had I not had the...

wcoomes- I had to use some of mine own washers and screws... ... ... from the junk bin in my garage! ;-) Not sure if they are shipping with hardware now... ..... I ordered mine a long time ago. Note: Instead of washers I use some small nuts to extend the latch for the cup holder. Also Note...

Adding my two cents: I have used the mag hytech on three different trucks and always fill to the top line of the dip-stick and never had an issue with "over filling". I can also tell you that I have had my share of pinion seals leak (front and rear) and in every case it was a defective seal or...

Brethren I too have had this happen to me many times!! I have found that if you pry from the top of the latch ... ... . it will release with no issues!! One would think that you need to pry from the bottom of the latch... . which is where you will screw it up. Sounds crazy but again if you...

Rcatalo- I just received my Borgeson steering shaft and after reading this post I am thinking about replacing my stock steering box with the Borgeson box... . sounds like it might be easier to do both. Note: I am on my third factory steering box and after 25k miles I am getting the "road...

Muddflapp- You got a nice looking truck and lucky enough to get the old faithful 5. 9 in it. ;-) As far as issue with your truck really the only big ticket item is front-end parts. I have had to replace everything in regards to steering parts. In fact I am on my third steering box... ... ...