Here I am

New England Wrench Day

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff

1st Ever Kansas City Diesel Club Meeting March 24th

March 17th - KCIR - Kansas City

Matt

I was hoping to leave the resonator in place, that puppt is 4" (I think) at its oulet and the pipe to replace the muff needs a bend, If I pitch the resonator will you method work without having to deal with the idiots at the muff shop to get the pipe bent? I don't know if there is a difference between yours and an 01.

Thanks

Mark
 
My bad... I didn't notice that you had an ISB.....

From what I've seen, the exhaust systems are very similar..... 3" downpipe... . 4" muffler inlet... . 3" muffler outlet... . 3" tailpipe... . it's just that the kitty kat and the resonator that are different.



As long as your downpipe and tailpipe are the same size... a straight length of pipe flared at both ends will work just fine. Last I knew... it was a straight shot from the DP to the tailpipe on the ISB's.....



Matt
 
Mark, Scotty's muffler here in San Bernadino did min for forty five bucks. They cut the Muffler and res. out and put in a new piece of pipe. They said it was easy. They welded the new piece in place and were done in 35 minutes. No resonator and no problems.



As far as March 16th goes. . . I will try to make it. Not having anything done, just thought it would be nice to meet a few of my new neighbahs. We found a home in Wakefield NH, and will be there on the 6th of march. So, depending on when (and if) the moving van arrives, I could sneak down for a morning cup'a joe!

Ya' think?
 
Newf, welcome to New England dont forget you dont have to pack your "R's" we have no use for that lettah heah. ;)



Does the pipe that was installed in yours have any bends in it?

Sounds like I'm gonna have to slide back under and eyeball it, see if I can do the muff and resonator with a straight pipe. Got an electrician friend who might be able to bend 3" fo me. Hate to drive over it with the Jeep to bend it.

I would also like to listen to one that has no res / kitty, muff in it on wrench day to make sure that on trips to Florida it won't keep me awake while I'm drivin. Louder is better (most of the time):D :D My Jeep is V8 headers straight pipe and sounds like a race car / out of controll Harley;)

Mark
 
i MAY be there

hey guys-- i may be there. it depends on how i feel coming off shoulder surgery. also depends on the weather as toni will have to drive. i wont be able to turn wrenches, but i'll have some mirrors to change if anyone wants to. hope i see y'all there.
 
Heyya John, gonna get some diving in? Vis should be good. Catch ya at the next meet. Bummer about having the TC/VB in for three weeks then trading my truck. Although, the thing did rip for those three weeks. SOme luck sob is gonna buy a used v-10 with Bill K's stuff in it.
 
i hear ya jeff , someone is going to get in a dodge with an auto and have it drive like it supposed to.



i see you bought a stick this time around , can't wait to check it out .
 
What lot is that 'ole V-10 on? :D

Maybe they wouldn't mind if a old 47RH suddenly finds a home in that V-10 powered beast... .

They don't need OD or lockup... . it's only gonna get 7mpg anyway!



Matt

On edit: Just changed my mind... I forgot you had 2wd... . I don't want to tear down a perfectly good transmission to swap out a tailshaft which is the LAST thing to come out... ... :p
 
Last edited:
MarkF, The pipe is straight. It raised my tailpipe up but only slightly. I had to really look to notice the difference.



Could someone email me directions to Massdiesel from say, the portland area. Heck, just what town it is in and directions from an interstate. Thanks alot. I won't have e-mail as of 2/25 until right about wrench day. Thanks in advance. Dennis
 
Directions to Massdiesels:



From rte 95

rte 1 south (in Sharon), go past Foxboro (CGMI) Stadium.

take a right at the next set of lights (rte 115) there is a restauraunt there that looks like an old white house.

take a right at the stop sign (this is now rte 115)

stay on rte 115 for about 4-6 miles, KTM motorcycle dealer is on the right, go behing this building and Massdiesel is he first two bays on the left.



From 495 South

left at the bottom of ramp (towards Franklin)

follow for 6 miles, to intersection of rte 115

take left onto rte 115,

follow 2 miles, KTM motorcycle dealer is on the right, go behing this building and Massdiesel is he first two bays on the left.





Have a safe trip, look forward to seeing you all there.

Oo.
 
Last edited:
WTF... ... ... I knew i $uck @ giving directions. MWheaton just e-mailed me to let me know how bad I did. Son-of-a-b!t(h. :{ :{ :{



Oh well, I tried.



Guys, here are some clarifications I was requested to add:



The afore mentioned exit 16 of 495

KTM dealer is a red building, you need to turn into their parking lot (before the building) and Massdiesels is down the dirt driveway.



HTH... ... ... ... ... ..... Oh & don't blame me if you get lost

:D OK, maybe you can blame me:rolleyes:
 
for the record....

I'm behind the curve. I didn't realize George had already posted. Looks a lot better than what I wrote.



... go to Norfolk, MA turn left at the construction and be careful when you cross the railroad tracks... . when you see a garage on your right, duck behind it and follow a short dirt road to MASSDIESEL's garage... you can't miss it :D



Good job George!



Matt
 
Whoa George... . It's just directions. Sheesh, from the response, you'd think someone told you you were gonna be driving a d-max the rest of your life.



The directions were fine.



Oh yeah george, are ya bringing your dog;)
 
Uh Jeff, please step away from the pooch:D No, I'm not taking my dog!



And, in case anyone took my above responses to be a little on the aggressive side... ... ... ... ... ... ... ... ... ... ... . your wrong:mad: there is nothing about me that is aggressive:mad: #@$%! Geese, sometimes people just take things the wrong way:eek:

Just remember, like Toolman said, you really can't tell the meaning behind someones words when your reading it and you can't see the menaing behing the words... ... ... ... ... or something like that :)



:)



Wheew, now I got that off my chest. I think I need a hug:D Before you offer Jeff... ... ... ... ... . I'm just kidding:D
 
Dennis

thanks for the info, I'm gonna try to get the pipe this afternoon or tomorow. Oo. Have a safe trip.

See ya'll on wrench day unless something comes up.

Mark
 
Wrench Day!!!

Hope to make it, nothing going on yet for that weekend. Just coming to watch and BS.



May be bringing someone else w/ their truck, not a member yet but working on him.
 
Yahoooooo

Just ordered my Volant intake (Backordered 'til March 21st :mad: ) I was hoping to bring that along and do an install... ... ... ... . Geez now I need to do somethin' else.



George I hear ya again on that one ;) Difference is tho My doctor says the medication can start to be weened off soon :p :D
 
Back
Top