Here I am

Recent Content by aphyfe

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff
  1. A

    Engine/Transmission (1998.5 - 2002) Nozzle pop pressure & torque

    Laing Diesel in Williamsport PA. 570-494-0874. I guess there is no harm in posting a good repot on a business or product, i don't think it is against the rules.
  2. A

    Engine/Transmission (1998.5 - 2002) Nozzle pop pressure & torque

    Had the injectors (jammer 3's) tested and re shimmed. 2 of them were very high (+30 bar) and the other 4 were about 20 bar low, They reshimmed and got them all within 1 bar. Runs very nice and power is great :-laf with the BD box turned off. Took some of the harsh rattle out of it too. The...
  3. A

    Engine/Transmission (1998.5 - 2002) Nozzle pop pressure & torque

    pressure 305 bar, Thankyou, I read that 33 ft/lbs for VW TDI injectors is reccommend, the unit is close to the same, so that will probably work. Some responses from any one who has tested these after installation and can tell me wht the average variation is before shimming to get them...
  4. A

    Engine/Transmission (1998.5 - 2002) Nozzle pop pressure & torque

    bump I would really like an answer! Anybody?
  5. A

    Engine/Transmission (1998.5 - 2002) Nozzle pop pressure & torque

    Bump :confused: Can't believe with all the "Knowledge" on here I can't get an answer!
  6. A

    Engine/Transmission (1998.5 - 2002) Nozzle pop pressure & torque

    I just got Jammer 3's and have not had them tested yet before install. I have cleaned and intstalled them in the bodies (one at a time of course to avoid mixing the parts up) What is the specified nozzle test pressure in psi and what variation is allowed or can be reasonably achieved? From...
  7. A

    Engine/Transmission (1998.5 - 2002) 3 Melted Pistons

    Hone Send it to a reputable shop and have it done right. Cummins hones these blocks with a torque plate installed at the factory, I don't know where you will find a shop with a plate for one of these. Insist on it even if you have to ship it half way across the country!
  8. A

    Engine/Transmission (1998.5 - 2002) VP pump + cut delivery valves = ?

    More info? What is the story? Any new info yet?
  9. A

    Engine/Transmission (1998.5 - 2002) Inexpensive boost fooler

    Thanks, I see BD has new ones for 59$ retail. Who is a BD dealer in the PA area and may give me a break?. If I had alittle more cash I might put an EZ on it. As usual this stuff is addicting!
  10. A

    Engine/Transmission (1998.5 - 2002) Inexpensive boost fooler

    Is there a such thing and where do i get it? I want to increase the boost a little but not set any codes. 2001 HO 6-spd stock except for 275'S and silencer ring removed. Truck was a very strong HO when it was stock and the 275's really helped and increased almost 3 mpg on the hwy!
  11. A

    Engine/Transmission (1998.5 - 2002) Injector Install

    Install Instructions Can I get some instructions please? Do the 275's help the stock '01 HO very much without a fueling box? How about mileage? I just got a set. -- email address removed -- Thanks!!
  12. A

    Engine/Transmission (1998.5 - 2002) Unbelievable amount of smoke!

    smokin' Reminds me of old days, when jets and diesels converted fuel into smoke and noise!!! Hope the guy at least clogged the air filter of the vehicles behind them!
  13. A

    2nd Gen Non-Engine/Transmission Brake light

    I have an intermittent brake light only on. It will come on solid, not flashing like the P-brake is on, then go out after a while. No ABS light though. It doesnt set any permanent codes but I got 2 codes out today: PCU P0460 and ECU P1693. Anyone know what they mean? 01. 5 CTD Six spd...
  14. A

    2nd Gen Non-Engine/Transmission Garnet paint falling off

    I have a 01. 5 St. Louie garnet red. I also noticed the paint is very soft, no peeling problems yet. Hope they don't start!!
Back
Top