Here I am

Recent Content by Gumbs77

Attention: TDR Forum Junkies
To the point: Click this link and check out the Front Page News story(ies) where we are tracking the introduction of the 2025 Ram HD trucks.

Thanks, TDR Staff
  1. G

    Slop in steering box revisited.....

    when you say slop revisited is that from adjusting it the first time? I had a lot of slop in the wheel and the adjustment took it right out.
  2. G

    Speedometer Just Checked Out......Bye..Bye!!

    Thats not good, Can I get one from a junk yard? Well I hope so. Thanks for the info I'll Let ya now how I make out. Jim
  3. G

    Speedometer Just Checked Out......Bye..Bye!!

    OK, on my way home today my speedometer checke out, Just stopped working. So I hop on the old TDR and start searching. I've had no luck:( so now I'm here to ask what could cause this. What I've done so far is found out that it's not the speed sensor in the transmission or the gear. And I know this...
  4. G

    JC Whitney Trac Bar

    Ya, I was after the trac bar for the front-end not the traction bars fore the rear-end but thanks for the info. I think I'll steer clear of those. Monday I will call and order lukes links. Thanks Jim
  5. G

    JC Whitney Trac Bar

    OOPS,:rolleyes: I didn’t even read the hole thing, sorry. but I think I'll try the luks link. It looks like the way to go, thanks Jim
  6. G

    JC Whitney Trac Bar

    OK, I replaced my trac bar with the factery track bar(Stupid me) and less then 5000mi it's shot (suprise suprise). i was wondering if anyone tried the trac bar from JC Whitney? JimJC Whitney Trac Bar
  7. G

    Hello, New here wanted to say Hi

    I was stock, After 3 weeks of reading some how I had a south-bend clutch and gauges sitting on the steps when I got home one day. (wonder how that happened) not to mention the cat runaway and took the muff and silencer ring with it. Oh well what can ya do. It's addicting so be very carful...
  8. G

    Have you guys seen this?

    Well... ... My buddy has a PSD and if your like me and have no money to pay for labor after the warrantee runs out. Just look under the hood of the PSD. I took one look at his and just shook my head and toled him good luck. You got to be a contortionist to work on those things. Besides I’m the...
  9. G

    Secret handshake to remove tension pully??? (Size of hex key)

    Never mind I guess you got it.
  10. G

    new starter price

    When I got my truck, the contacts were bad. :mad: Cost me less than 8$ for new ones at my local starter rebuild place and about hour of my time. Popping the starter out is no big deal. The best thing to do is pop it off and take it apart. Just look out for the little ball on the other end of...
  11. G

    Guage Install Problem

    Yes, Do check the polarity. Most of the wiring that i’ve done red is + and The Black is - but on the autometer gauges, red is the - and yellow is the +. Good luck!! Jim
  12. G

    We have gauges.....take two!

    I just installed mine to, my boost tops off at 16psi WOT and truck empty, 1100 WOT on the EGT. I have my stock plate slid all the way forword and the AFC housing all the way forword and the star wheel all the way in. No cat or muffler. :D Moparguy filter installed. Have no clue if that's good...
  13. G

    "MAKING" a dealer honor warranty...

    warranty ??? Whast that?:eek: Sorry, The only warranty that i get is 50' or the end of the driveway:p Jim
  14. G

    Is this a reasonable price quote?

    If you would like some help will give it, but I think you mite want to fill us in on your location or at least your state.
  15. G

    Value of '94 Ram????

    I just bought my 94 4x4 reg. cab, laramie just pade 9,000 with 120k and a small spot of rust on the lower drivers side door. Jim
See more
Back
Top