Competition Franklin Indiana Sled Pull...Video....

[zstroken]

Justin,

Did you get any video of the black 01 from noblesville?

 

[jwilliams3]

Yeah,

I'll have it up shortly.

 

[zstroken]

If you can put up both hooks. I was unable to attend do to a certain 1997 dodge giving me fits!!

 

[jwilliams3]

I only have one.

The guy shootin for me didnt get my 2nd hook either.



-Click here to see Video

 

[jwilliams3]

Jim,

Its a Midwest 450!

 

[Bobcat698]

Nothing broken here



Made it home just fine



Check out another video angle here:

-Click here to see Video

Hey did anyone notice in Garrett Sheilds video (Bobcat798) that it sounds like he broke something (sounds like a pinion) about 50 feet into it?



-Click here to see Video





I can't tell if the noise is from the bleacher area or the truck?

Hopefully he made it home ok.

 

[Bobcat698]

I drove 7 hours to pull out there, in the truck I pulled with!



I didn't think I did too bad taking the #5 spot out of 22 trucks!



Justin forgot to post:

#4: Bryan Brewitt 283. 05 ft

#5: Garrett Shields 274. 06 ft





Anyone else see the daylight under the left front tire? :-laf :-laf



#ad

 

[BigBadDodge]

Nice picture, really shows the flexing that takes place in the frame and body. Do you plan on hanging any wieght? what does she wiegh as pictured?



BBD

 

[BigBadDodge]

I do miss driving to the pulls and then driving home. But I don't miss the chocolate star fish on the driver seat my ***** left after the pull hoping I could drive home :-laf



BBD

 

[Bobcat698]

Nice picture, really shows the flexing that takes place in the frame and body. Do you plan on hanging any wieght? what does she wiegh as pictured?



BBD

7950 as pictured. It weighs just under 7k with a full tank of fuel IIRC, but I travel to a lot of the pulls, so there is luggage :-laf



I am going to see about getting a weight wrack built before Indy Oo.

 

[RSlaughter]

nice job this weekend... but where the super smokey vid of our truck??

green/silver FINALLY lit up about 175 ft mark

not bad i guess for the first run on the new motor/chassis setup...





Roy

 

[JDailey]

That was one of the worst pulls I've ever been to. Nice job Justin! Bobcat-I would check your spider gears. And get a set of bars on that thing man! Is there any paint left on the front of the fenderwells?

 

[RSlaughter]

yeah the whole setup pretty much sucked

 

[bgilbert]

Justin did anyone get a vid of that white 1st gen?

 

[jwilliams3]

I'll check my footage see if its on there.

I should have a complete video within a couple weeks (at least I hope so).



-Click here to see Video

 

[bgilbert]

Thanks Justin. Looks like it would've smoothed out if he kept on it. I know he broke his D70 a few years ago at Scheid's bouncing like that.

 

[Bobcat698]

Ha! Just had them replaced, one broke in half... . But it IS in the shop for a brake fluid leak and they will be checking the rear end again as there is material on the drain plug again. .



What are you referring to about the paint on the fenderwells?? Maybe I'm a little slow. .

 

[Bobcat698]

Oh Crap! :{

Spider gears are all shot, the cross piece is broke, ABS ring is shot.

Only thing that is good is the carrier & ring & pinion.

 

[zstroken]

Did you get the pictures I sent of the ladder bars?

 

[Bobcat698]

Did you get the pictures I sent of the ladder bars?

Yes. Thank you. Looks like the fund will be short now. . Need a locker...