I have most ALL 1st gen parts new or used

[Simplysmn]

I have a guy that is working on a 2 piece alum Shroud for our truck's Hang in there they will be Ready soon .

 

[Mikey-KE7LBB]

I have a guy that is working on a 2 piece alum Shroud for our truck's Hang in there they will be Ready soon .

I've been trying to get the local machine shop to build one for me, but it seems like they are not interested.

Please PM me when they are available.

 

[Simplysmn]

Yes Sir I will there is a Hard market for 1 for sure and being 2 piece will make it even Easier .

 

[CTaylor]

This may interest me as well

 

[Dirtscience]

I am also looking for plastic interior trim pieces. Just starting to try and restore my old truck and these seem to be the hardest parts for me to find. Also need another dash mine has a giant hole in the middle of it.

 

[CTaylor]

I think this thread has pretty much played out. I don't think the OP has been around in quite sometime

 

[Dirtscience]

Teach me to reply to a thread from 2014. Shoulda looked closer!

M

 

[yamastomper]

I am looking for a gray drivers side arm rest. The plastic inside mine is broken so its hard to close the door. Do you by chance have one?

 

[DonFitzwater]

I am looking for a gray drivers side arm rest. The plastic inside mine is broken so its hard to close the door. Do you by chance have one?

You should email the op. That's why he provided his email.

 

[Andy314]

I called and sent an email..

 

[CTaylor]

I called and sent an email..

Did you get any kind of answer?
He shows to have been on here about a week ago so he is still around it seems.

 

[apclown]

I need the fuel tank /gauge sending unit for my 1991 D250 2WD. Can you help?

 

[Randy DeBaillie]

Hello, looking for power ram diesel fender emblems for 1990 w 250 . New to like new. Thanks, Randy. 309-781-5218

 

[Ashley Claire Schexnayder]

I am looking for a speedometer/odometer gear replacement. My current has the broken gears for the odometer, and the speedometer circuit board is fried. I am willing to go with an aftermarket set up if anyone has any advice on that also.

 

[Simplysmn]

I am looking for a speedometer/odometer gear replacement. My current has the broken gears for the odometer, and the speedometer circuit board is fried. I am willing to go with an aftermarket set up if anyone has any advice on that also.

You can get a different cluster if your interested Send me a PM I also have some Grey interior part's along with door panel's and other stuff.

 

[Rick Keen]

Hi all, I have most ALL 1st gen parts new or used. If I don't have it. I can reverse engineer it and make it in house or have it produced .. It is just a matter of how many and how much. I have many parts that were only offered to the fleets . Never to the public. I have redesigned many of the "problem parts" to be more reliable and last longer than the orginials. I DO NOT MAKE RACE CAR PARTS. No need to ask how to make 1000 hp or do 10 second quarter mile runs. Most on the site know me. I am a retired Chrysler engineer. I worked on the original Cummins/Dodge truck development project that started back in 1983.

 

[Rick Keen]

Throttle position sensor on 1993 D250, auto trans. With Cummings?

 

[BigPapa]

RockAuto has one for $36.

-Scott

 

[Simplysmn]

E bay has them for anywhere from 9.00 and up

 

[Huey3476]

I have 1990 dodge d350 2wd. I am Low vacuum warning sensor, a 2wd solid axle and a dana 70 dually rear end.